NKNP1/2W0.82OHMJT/B datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> NKNP1/2W0.82OHMJT/B

NKNP1/2W0.82OHMJT/B: DescriptionFixed Resistor, Wire Wound, 0.5W, 0.82ohm, 5% +/-Tol, -300,300ppm/Cel,; CategoryPassive components The resistor; File Size179KB，7 Pages; ManufacturerTY-OHM Electronic Works Co., Ltd.; Environmental Compliance

Download Datasheet Parametric View All

NKNP1/2W0.82OHMJT/B Overview

Fixed Resistor, Wire Wound, 0.5W, 0.82ohm, 5% +/-Tol, -300,300ppm/Cel,

NKNP1/2W0.82OHMJT/B Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	947484619
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Flameproof
Lead diameter	0.65 mm
Number of terminals	2
Maximum operating temperature	200 °C
Minimum operating temperature	-55 °C
Package diameter	3 mm
Package length	9 mm
Package form	Axial
method of packing	Tape
Rated power dissipation(P)	0.5 W
resistance	0.82 Ω
Resistor type	FIXED RESISTOR
series	NKNP
technology	WIRE WOUND
Temperature Coefficient	300 ppm/°C
Tolerance	5%

Preview

Download Datasheet

View All

NON-INDUCTIVE RESIN PAINT WIRE WOUND RESISTORS

7.4 Insulation Character :

Resistors are located in a V-shaped metal trough. Using the DC 500V megger instrument 2 poles to

clutch either side of lead wires and metal trough, measuring the Insulation Resistance which shall be

over 1000MΩ.

7.5 Voltage Withstanding:

Resistors are located in a V-shaped metal trough. Applying suitable voltage listed on DIMENSION

for one minute and should find no physical damage to the resistors, such as arc, char...etc.

7.6 Load Life:

The resistors arrayed are sent into the 70℃ oven, applying rated voltage at the cycle of 1.5 hours

ON, 0.5 hour OFF for 1000

+48

hours in total. Then, after removing the voltage, take the resistors out

-0

of the oven and left under normal temp. for one hour cooling. The resistance value change rate

between pre-and-post test shall be within ±3%.

7.7 Moisture-proof Load Life:

The resistors arrayed are placed into a constant temp./humidity oven at the temp. of 40 ±2℃ and the

humidity of 90½95%, then 1/10 DC rated power is applied for 1.5 hours and cut off for 0.5 hour.

The similar cycle will be repeated for 500

+24

hours in total (including cut-off time). Then remove the

-0

voltage, taking the resistors out of the oven and leaving them at room temp. for one hour. The

resistance value change rate between pre-and-post test shall be within ±3%. There also shall be no

evidence of remarkable change on appearance, and the marking shall not be illegible.

7.8 Solder-ability:

The leads with flux are dipped in a melted solder of 235 ±5℃ for 2 seconds, more than 95% of the

circumference of the lead wires shall be covered with solder.

7.9 Resistance to Soldering Heat:

Two leads are together dipped in a melted solder of 270 ±5℃ for 10 ±1 seconds, or 350 ±10℃ for

3.5 ±0.5 seconds, Then remove the resistors and leaving them at room temp. for one hour. The

resistance value change rate between pre-and-post test shall be within ±1%.

7.10 Nonflammability:

The resistors are applied the power of 16 times the rated wattage for 5 min. and shall not get flame.

7.11 Inductance:

It shall be less than 1μH.

4 of 6

Recommended Resources

Contact switch or proximity sensor circuit

15V power supply circuit diagram with good filtering effect

"AND" logic element configuration circuit

Universal mobile phone charging road map

Low power instrument amplifier circuit

Highly sensitive static electricity detector circuit

Why does the voltage of C46 become normal after replacing a larger capacitor?: After mounting the chips according to the circuit diagram, the voltage at VCC3V3 is not 3.3V, but 4.6V. After C46 is replaced from 22pF to 330pF, the voltage at VCC3V3 is 3.3V (the required voltage is...; 梅花飘落孤人醉 Analog electronics

I'd like to ask if anyone has this tutorial.: [i=s]This post was last edited by sunboy25 on 2021-6-3 11:15[/i]I would like to ask if anyone has the reference for active filters in Chapter 3 of Circuit Design Based on Operational Amplifiers and An...; sunboy25 Analog electronics

E-sports preparation experience: The national electronic competition is still difficult. Within the specified time, that is, 4 days and 3 nights, we need to make electronic competition questions with high standards and high requireme...; 念慈菴 Electronics Design Contest

CH224K test QC2.0 protocol 9V+E-Mark function: [i=s]This post was last edited by Yunhu Congbai on 2022-9-3 15:28[/i]Ask for forgivenessIn fact, I had already received the board a long time ago, printed out the chip manual, and read it many times.I...; 韵湖葱白 Domestic Chip Exchange

[Qinheng Trial] Single-step simulation: I remember that the STC microcontroller has a chip that can be used for single-step simulation. I didn't expect Qinheng to be able to do it, so I tried it today and it works well. It’s actually very s...; ddllxxrr Domestic Chip Exchange

Help with MSP430FG479 library: Help with MSP430FG479 library...; ~胖球 Microcontroller MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components