Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[i=s]This post was last edited by littleshrimp on 2021-6-28 15:28[/i]Main official information search
Most of the materials used in development can be indexed and searched through the index.html in th...
Silicon Labs BG22-EK4108A Development Kit Connect the Future with Technology Application in Progress!Click to applyApplication period:
From now until December 5, 2021
1. Click the "I want to apply" bu...
[i=s]This post was last edited by qwqwqw2088 on 2019-11-21 11:52[/i]Balun (Balun: Balance-UnBalance) can achieve the conversion between single-ended and differential structures. However, the cheapest ...
[i=s]This post was last edited by jone5 on 2021-7-27 21:58[/i]The purpose of applying for this kit is to make a tooling fixture, with the goal of understanding the chip's additional clock, IO, ADC, PW...
What are your graduate supervisors like? My supervisor is very nice and responsible to me. I don’t know if he is too responsible or if he is bored at home, but he criticized me harshly when he was hel...
On December 6, CITIC Securities released information disclosure on the filing of Foshan Weida Optoelectronic Materials Co., Ltd.'s public offering of shares to unspecified qualified investors and lis...[Details]
Power devices
The thermal stress they are subjected to during application may come from two aspects: inside the device and outside the device. The power dissipated by the device duri...[Details]
At present,
the application of
frequency converters
has expanded from common fans and water pumps to food, beverages, logistics, buildings, etc., and has continuously opened up new energy-sa...[Details]
The inspiration for location services comes from the PMB2520 single-chip Assisted Global Positioning System (A-GPS) solution called "Hammerhead", jointly developed by Infineon and its US partner Gl...[Details]
In accordance with the Environmental Impact Assessment Law of the People's Republic of China and the Measures for Public Participation in Environmental Impact Assessment (Order No. 4 of the Ministr...[Details]
The belt conveyor transmission system is an important part of the underground coal mine transportation system, and is also the main component of coal mining enterprises' energy consumption. In rece...[Details]
South Korean media revealed that Samsung Electronics is embarking on a comprehensive organizational restructuring aimed at optimizing internal communication and collaboration processes to enhance t...[Details]
The APQP manual mentions product special characteristics and process special characteristics, but KPC and KCC appear in other AIAG manuals. The relevant English of these words is as follows:
P...[Details]
According to official news from Samsung, five of Samsung's memory products have recently been certified by the Carbon Trust for successfully reducing carbon emissions. According to reports,...[Details]
RC bridge oscillator circuit
Use an oscilloscope to observe the output waveform of the oscillation circuit. If there is no output waveform or the output waveform is obviously distorted, Rp shoul...[Details]
From dead trees to lush leaves, from warm spring to midsummer, in three months, the staff size of Mitsubishi Electric China Co-Creation Center has nearly doubled. On July 1, 2022, Keiichiro Suzuki, d...[Details]
The purpose of network analyzer calibration is to eliminate systematic errors in testing. The idea of calibration is to obtain the specific value of the network analyzer system error term by testin...[Details]
1.
Impedance calculation
All audiophiles with basic knowledge know that the square of the ratio of the number of turns of the primary and secondary sides of the transformer coil is equal to the...[Details]
What is the reason for the unstable speed of the inverter?
There may be many reasons for the unstable speed of the inverter, the most common ones include:
Load change: When the load chang...[Details]
August 21, 2024 –
Mouser Electronics, an authorized global distributor of electronic components and industrial automation products focused on New Product Introduction (NPI), is now stocking the...[Details]
ST - Low Power RF
京公网安备 11010802033920号
EEWORLD
