USR UNR 4-3425
FEATURES
•
•
•
•
•
Resistances from 0.05Ohm to 500Ohms
Power Rating to 50Watt
Resistance Tolerances to ±0.01%
TCR to ±1ppm/K
Load Stability to 0.01%
TABLE 1—SPECIFICATIONS
TYPE
Resistance Range
Power Rating
Free air 70°C
With heatsink
USR 4-3425
UNR 4-3425
0.05 to 650 Ohms
other resistance values upon request / power rating depending
on resistance value
3W (available with heat sink on backside: 5W)
30W
50W
Tolerances
from 0.05 Ohms
from 10.0 Ohms
from 50.0 Ohms
Thermal Resistance
Stability (1000h)
Shelf Life Stability
Temperature Coefficient
Voltage Proof
Maximum Current
Thermal EMF
Operating Temperature Range
Resistor Material
Substrate
Housing
Connector Material
Terminals
Max. Torque
Notes
0.1% / 0.25% / 0.5% / 1%
0.05% / 0.1% / 0.25% / 0.5% / 1%
0.01% / 0.02% / 0.05% / 0.1% / 0.25% / 0.5% / 1%
3.5 K/W
2.1 K/W
0.01%
25ppm / ∆R after 1 year
50ppm / ∆R after 3 years
max. ±5ppm/K (-55 to 155°C)
typ. ±3ppm/K (-55 to 125°C)
typ. ±1ppm/K (25 to 60°C)
upon request ±1ppm/K (0 to 60°C)
750 VDC
15A
< 0.1µV/K
-55 to 155°C
NiCr-Foil
Al
2
O
3
Epoxy + Al-heatsink
Cu / tinned
4 (standard contact D)
1 Nm
Specially designed for ap-
plications with fast changing
electrical load
AlN
ORDERING INFORMATION
Part Number - Resistance - Contact - Tolerance - TCR (if not standard)
USR 4-3425 10R000 D 0.5% 1ppm/K (0 to 60°C)
Document No.: 64223
Revision: 03-05-2016
For technical questions,
contact
powertron@vpgsensors.com
www.powertron.de
1
USR UNR 4-3425
FIGURE 1—TEMPERATURE COEFFICIENT
200
100
0
∆R/R
(ppm)
-100
-200
-300
-400
-500
-600
-700
-75
-50
-25
0
25
50
Temperature (°C)
75
100
125
Nominal Spread
±2.3ppm/K
150
Nominal
∆R/R
Nominal Spread
±2.3ppm/K
FIGURE 2—DERATING
Power Rating Notes -
The U-Series Resistors must be attached to a suitable heatsink.
The maximum internal resistor temperature is 155°C.
To specify an appropriate heatsink use the following formula :
Power (% from
nominal power)
120
100
80
60
40
20
0
25
50
85
100
115
130
145
155
R
qH
= T
MAX
- ( P x R
qR
) - T
A
P
Where:
R
qH
= Thermal Resistance of Heatsink ( K/W )
R
qR
= Thermal Resistance of Resistor ( K/W )
T
MAX
= Maximum Temperature of Resistor
T
A
= Ambient Temperature of Heatsink ( °C )
P = Power Through Resistor ( W )
Temperature of the backplate(°C)
FIGURE 3—DIMENSIONS
in mm (inches)
Dimension
A
±2.0 (±0.079)
B
±0.3 (±0.012)
C
±0.2 (±0.008)
D
±0.2 (±0.008)
E
±0.1 (±0.004)
F
±0.2 (±0.008)
G
±0.1 (±0.004)
H
±0.1 (±0.004)
I
±0.2 (±0.008)
J
±0.2 (±0.008)
K
±0.1 (±0.004)
L
±0.1 (±0.004)
M
±0.2 (±0.008)
50.00 (1.97)
34.00 (1.34)
25.00 (0.98)
10.00 (0.39)
5.00 (0.20)
17.80 (0.70)
Ø3.50 (Ø0.14)
Ø0.8 (Ø0.031)
27.50 (1.08)
17.50 (0.69)
2.00 (0.08)
4.50 (0.18)
3.00 (0.12)
www.powertron.de
2
For technical questions,
contact
powertron@vpgsensors.com
Document No.: 64223
Revision: 03-05-2016
Legal Disclaimer Notice
Vishay Precision Group, Inc.
Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in
any other disclosure relating to any product.
The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but
not limited to, the warranty expressed therein.
VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase.
To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the
application or use of any product, (ii) any and all liability, including without limitation special, consequential or
incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose,
non-infringement and merchantability.
Information provided in datasheets and/or specifications may vary from actual results in different applications and
performance may vary over time. Statements regarding the suitability of products for certain types of applications
are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s
responsibility to validate that a particular product with the properties described in the product specification is suitable for
use in a particular application. You should ensure you have the current version of the relevant information by contacting
VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com.
No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any
conduct of VPG.
The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise
expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do
so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale.
Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such
applications.
Product names and markings noted herein may be trademarks of their respective owners.
Copyright Vishay Precision Group, Inc., 2014. All rights reserved.
Document No.: 63999
Revision: 15-Jul-2014
www.vpgsensors.com
1
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
