EEWORLDEEWORLDEEWORLD

Part Number

Search

MJ27-44EA

Description
Telecom and Datacom Connector, 4 Contact(s), Male, Right Angle, Solder Terminal, Locking, Jack
CategoryThe connector    The connector   
File Size212KB,1 Pages
ManufacturerRatioplast Electronics
Download Datasheet Parametric View All

MJ27-44EA Overview

Telecom and Datacom Connector, 4 Contact(s), Male, Right Angle, Solder Terminal, Locking, Jack

MJ27-44EA Parametric

Parameter NameAttribute value
MakerRatioplast Electronics
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsSPLIT BOARD LOCK
body width0.571 inch
subject depth0.591 inch
body length0.559 inch
Body/casing typeJACK
Connector typeTELECOM AND DATACOM CONNECTOR
Contact to complete cooperationAU ON NI
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
Contact resistance20 mΩ
Contact styleTELCOM, MODULAR
Dielectric withstand voltage1400VAC V
Durability500 Cycles
Insulation resistance500000000 Ω
Insulator colorGRAY
insulator materialGLASS FILLED POLYBUTYLENE TEREPHTHALATE
Manufacturer's serial numberMJ27
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of ports1
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
PCB contact patternSTAGGERED
Plating thicknessFLASH inch
Rated current (signal)1.5 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.032 mm
Termination typeSOLDER
Total number of contacts4
SIDE ENTRY UP LATCH MODULAR PCB JACK 4P+6P+8P+10P PROFILE=14.50MM
(UNSHIELDED)
SPECIFICATIONS
Insulation Resistance:
500MΩ
Min.
Contact Resistance:
20mΩ
Max.
Rating Current:
1.5A Max.
Rating Voltage:
120V AC.
Dielectric Voltage:
1000 Vrms 60 Sec. Min.
Temperature Range:
-40ºc / +85ºc
Durability:
500 Mating cycles Min.
MATERIALS
Housing:
PBT Glass Filled (UL 94V-0)
Soldering Temperature:
235ºc
Color:
Black & Gray
Spring Wire:
Phosphor Bronze
Gold plating Over Nickel
All materials must be RoHS compliant.
Recommended P.C.Board Layout
(TOP VIEW)
MJ26
MJ27
No. of
No. of
A
B
C
Positions Contacts
(6P)4P
4C
12.20 7.85 12.00
6P
2C/4C/6C 12.20 9.90 12.00
8P
8C
15.00 11.85 15.00
10P
10C
15.00 11.85 15.00
D
14.20
14.20
16.90
16.90
ORDERING INFORMATION:
P/N M J x x - x x x x x
1
2 345
1. PANEL STOP OPTION:
"26" WITH PANEL STOP
"27" W/O PANEL STOP
2. NO. OF POSITIONS & CONTACTS:
"66" 6P6C
"64" 6P4C
"88" 8P8C
"00" 10P10C
"44" 4P4C
3. CONTACT FINISH:
"A" 6 MICROINCH GOLD
"B" 15 MICROINCH GOLD
"C" 30 MICROINCH GOLD
"D" 50 MICROINCH GOLD
"E" GOLD FLASH
4. HOUSING COLOR:
"B" BLACK
"A" GRAY
5. KEYWAY & OFFSET OPTION:
" " W/O KEYWAY & W/O OFFSET LETCH
"K" WITH KEYWAY (8P & 10P)
"D" WITH OFFSET LATCH (6P ONLY)
J234
[RISC-V MCU CH32V103 Review] + Hardware SPI drive OLED display DHT11 temperature and humidity
Last time I drove a DHT11 and used the serial port to output temperature and humidity. In order to display the sensor information, I added a 0.96-inch OLED screen to display it. It was still the last ...
eew_VHNtMb Domestic Chip Exchange
Multi-channel LED driver
Attached is the specification of the step-down constant current chip used to drive LEDs. I want to use this chip to drive multiple LEDs, such as four RGBW channels. I thought of a way to use four MOS ...
cpfpost Power technology
Application of Single Bus Protocol Converter in Distributed Measurement and Control System
Abstract: This paper introduces the main features, working principle and interface technology of DS2480B UART/RS232 to single bus protocol converter, and specifically explains the application of DS248...
rain MCU
Which formaldehyde sensor is good? Which model? If you have used it, please share and discuss.
Which formaldehyde sensor is good? Which model? If you have used it, please share and discuss....
damiaa Sensor
X-NUCLEO-IKS01A3 sensor test based on STM32F401RE development board 4 LIS2MDL magnetometer test
It took me several days to test the LIS2MDL magnetometer. I encountered a problem with the display of data. The value returned from the sensor is a 16-bit signed integer. At first, I used binary metho...
hujj MEMS sensors
Issues that need attention when initializing SPI of TI C2000 series 280049 chip
When the 280049 chip uses TI's library function, the register settings do not change after SPIA initialization, all are 0. At this time, you need to enable SPIA or SPIB. This problem has troubled me f...
Jacktang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号