EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN2208H1093BBT0

Description
RESISTOR, THIN FILM, 0.75 W, 0.1 %, 50 ppm, 109000 ohm, SURFACE MOUNT, 2208, CHIP
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

PTN2208H1093BBT0 Overview

RESISTOR, THIN FILM, 0.75 W, 0.1 %, 50 ppm, 109000 ohm, SURFACE MOUNT, 2208, CHIP

PTN2208H1093BBT0 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerVishay
package instructionSMT, 2208
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangul
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length5.309 mm
Package formSMT
Package width2.489 mm
method of packingTR
Rated power dissipation(P)0.75 W
Rated temperature70 °C
resistance109000 Ω
Resistor typeFIXED RESISTOR
size code2208
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrie
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage150 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
Sampling Theorem-------------What is the relationship between the detected signal and the ADC sampling rate?
Sampling Theorem-------------What is the relationship between the detected signal and the ADC sampling rate? Since the frequency of the electrical signal of the pelvic floor muscles is between 20Hz an...
QWE4562009 Test/Measurement
Showing off the products + CSR development board 10 years ago, when the Bluetooth market was just beginning to develop!
I won’t introduce it if I look at the pictures. . ....
samhuang8204 Special Edition for Assessment Centres
LIN communication wake-up question
The LIN 2.1 standard states that each slave node must be ready to receive commands (frame headers) from the host within 100ms from the end of the dominant pulse of the wake-up signal. However, in real...
喜鹊王子 Automotive Electronics
An introduction to TI's high-efficiency integrated power supply selection and reference designs
Texas Instruments' high-efficiency integrated power suppliesTI's broad portfolio of power management ICs supports the needs of NXP processors and Xilinx FPGAs. As can be seen from our complete referen...
fish001 Analogue and Mixed Signal
About the problem of the ambient light sensor of the rsl10-sense-gevk board not working well
Recently, some netizens found that the initialization of the NOA1305 ambient light sensor failed when testing the official routines, such as https://en.eeworld.com/bbs/thread-1166273-1-1.html . I also...
littleshrimp onsemi and Avnet IoT Innovation Design Competition
Can someone please help me analyze this transistor circuit? Is this parallel voltage negative feedback or parallel current negative feedback?
This is the circuit diagram:This is the simulation result:Please help me analyze the circuit, I will be grateful...
bqgup Innovation Lab

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号