EEWORLDEEWORLDEEWORLD

Part Number

Search

T215C396K020BS4251

Description
Tantalum Capacitor, Tantalum (dry/solid)
CategoryPassive components    capacitor   
File Size640KB,16 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Download Datasheet Parametric View All

T215C396K020BS4251 Overview

Tantalum Capacitor, Tantalum (dry/solid)

T215C396K020BS4251 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerKEMET
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance39 µF
Capacitor typeTANTALUM CAPACITOR
diameter7.34 mm
dielectric materialsTANTALUM (DRY/SOLID)
JESD-609 codee0
leakage current0.003 mA
length17.42 mm
Installation featuresTHROUGH HOLE MOUNT
negative tolerance10%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formAxial
polarityPOLARIZED
positive tolerance10%
Rated (DC) voltage (URdc)20 V
surface mountNO
Delta tangent0.06
Terminal surfaceTin/Lead (Sn60Pb40)
Terminal shapeWIRE
Tantalum Hermetically Sealed/Axial Through-Hole Capacitors
T215 Series High Temperature Solder
Overview
The KEMET T215 High Temperature Solder Series is targeted
for use in high humidity environments. These capacitors are
ruggedly built, designed for miniaturized circuitry, and especially
well-suited for coupling, bypass, filtering, and RC timing circuits.
The T215 Series exhibits excellent stability as well as extremely
low DC leakage current, dissipation factor and ESR/impedance
over a wide temperature and frequency range. The internal
design of these devices, as well as the hermetic seal, includes
high temperature solder (minimum melting point of 221°C). The
content of tin in the solder does not exceed 97%.
This assembly is especially suited for temperature conditions
where solder may fail due to undesirable solder reflow.
The KEMET T215 Series is available in standard EIA capacitance
values from 0.0047 µF to 330 µF in ±20%, ±10% and ±5%
tolerances, and working voltages of 6 VDC to 100 VDC and low
ESR limits.
Benefits
• Internal construction solder to resist up to 221ºC
• Qualified to MIL–PRF–39003, Style CSR13
• Failure rate options: Graded - B, C, D, and G, and
Exponential - M, P, R, and S
• Operating temperature range of -55˚C to +125˚C
• Capacitance values of 0.0047 μF to 330 μF
• Tolerances of ±5%, ±10% and ±20%
• Voltage rating of 6 VDC – 100 VDC
• Surge current options D, E, and F
• Taped and reeled per EIA Specification RS-296
• Marking per MIL–STD–1285
• Case sizes: A, B, C, D
Applications
Typical applications include coupling, bypass, filtering, and RC
timing circuits in miniaturized circuitry.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2064_T215 • 6/11/2013
1
Has anyone successfully mounted a USB flash drive with GD32+FATFS? Please advise
The current STM32105+FATFS 0.13C can be mounted on a USB flash drive normally.The code remains unchanged, only the STM32 on the board is replaced with GD32F105, and the USB flash drive cannot be mount...
mini_peng GD32 MCU
【i.MX6ULL】Driver Development 1——Character Device Development Template
The previous articles (starting from i.MX6ULL Embedded Linux Development 1-Preliminary Exploration of Uboot Transplantation ) introduced the system transplantation of embedded Linux (Uboot, kernel and...
DDZZ669 ARM Technology
What are the components FB1 and FB2 on the lpc824 DIP development board?
Recently I took a look at the information of the lpc824 DIP development board and found that there are two components FB1 and FB2 on the board, which are used to connect AGND and DGND. The schematic s...
bigbat NXP MCU
Can signaltap be set to automatically trigger after power-on? I encounter abnormal counting after power-on.
The debug script reads out that a register is 1 after power-on. This section of code is generated by a for loop. The initial values of the other registers are normal and there is no problem with the t...
qan FPGA/CPLD
Share some practical tips
Embedded systems inevitably have to deal with chip registers, and register operations require bit operations. I won’t talk about the basic operations such as clearing a bit and setting a bit, but let’...
成风 Programming Basics
Experts, please explain the relationship between the various layers of the PCB
I have used protel 99 and AD 17, and I have been drawing low-speed PCBs. Although I have been in the industry for many years, I have not studied PCB knowledge in depth. Recently, I want to learn orcad...
bigbat PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号