EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

SMC11004322FLF13

Description
Fixed Resistor, Metal Glaze/thick Film, 1W, 43200ohm, 350V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2512, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size161KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

SMC11004322FLF13 Overview

Fixed Resistor, Metal Glaze/thick Film, 1W, 43200ohm, 350V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 2512, ROHS COMPLIANT

SMC11004322FLF13 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerTT Electronics plc
package instructionMELF, 2512
Reach Compliance Codecompliant
structureCylindrical
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package diameter3.1 mm
Package length6.35 mm
Package shapeRECTANGULAR PACKAGE
Package formMELF
method of packingTR, 13 INCH
Rated power dissipation(P)1 W
Rated temperature70 °C
resistance43200 Ω
Resistor typeFIXED RESISTOR
size code2512
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage350 V
Pads automatically, vias not showing after drilling
When using automatic drilling, the vias are not displayed normally, but they can be seen when moving the traces. How can this problem be solved?...
天天1 PCB Design
Purgatory Legend-FIFO War.pdf
Purgatory Legend-FIFO War.pdf...
雷北城 EE_FPGA Learning Park
Op amp differential attenuation circuit problem
I want to use an op amp to make a voltage attenuation circuit to measure 3~48V DC signals. Attached is a preliminary circuit diagram, but the power frequency interference problem cannot be solved duri...
jesseyuan Analog electronics
[ESP32-Audio-Kit Audio Development Board Review] IR Infrared Remote Control LED Light
With the IR infrared receiving module as an accessory, the development board can remotely control the LED light. Its overall structure is shown in Figure 1. Figure 1 Overall composition The pin connec...
jinglixixi RF/Wirelessly
Dismantling and Renovation of Old LED Bulbs
An LED lamp at home is broken. This is a common 9W LED bulb. Since it cannot be used, I thought of disassembling it and analyzing it.It is easy to disassemble. Just squeeze the lampshade in front and ...
dcexpert DIY/Open Source Hardware
Emitter follower principle and typical circuit
[size=4][color=#000000][backcolor=white]Typical circuit of emitter follower:[/backcolor][/color][/size] [size=4][color=#000000][backcolor=white] [/backcolor][/color][/size] [size=4][color=#000000][bac...
Jacktang Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号