W78C33BM-24 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > W78C33BM-24

Preview

W78C33BM-24: Description8-BIT MICROCONTROLLER; File Size88KB，15 Pages; ManufacturerWinbond Electronics Corporation; Websitehttp://www.winbond.com.tw

Download Datasheet Compare View All

W78C33BM-24 Overview

8-BIT MICROCONTROLLER

Preview

Download Datasheet

View All

Preliminary W78C33B

8-BIT MICROCONTROLLER

GENERAL DESCRIPTION

The W78C33B microcontroller supplies a wider frequency range than most 8-bit microcontrollers on

the market. It is functional compatible with the industry standard 80C32 microcontroller series except

the one extra 4-bit bit-addressable I/O port (Port 4).

The W78C33B contains four 8-bit bidirectional parallel ports, three 16-bit timer/counters, and a serial

port. These peripherals are supported by a six-source, two-level interrupt capability. There are 256

bytes of RAM, and the device supports ROMless operation for application programs.

The W78C33B microcontroller has two power reduction modes, idle mode and power-down mode,

both of which are software selectable. The idle mode turns off the processor clock but allows for

continued peripheral operation. The power-down mode stops the crystal oscillator for minimum power

consumption. The external clock can be stopped at any time and in any state without affecting the

processor.

FEATURES

•

8-bit CMOS microcontroller

•

Fully static design

•

Low standby current at full supply voltage

•

DC-40 MHz operation

•

256 bytes of on-chip scratchpad RAM

•

ROMless operation

•

64K bytes program memory address space

•

64K bytes data memory address space

•

Four 8-bit bidirectional ports

•

One extra

4-bit bidirectional port

•

Three 16-bit timer/counters

•

One full duplex serial port

•

Boolean processor

•

Six-

source, two-level interrupt capability

•

Built-in power management

•

Packages:

−

PLCC 44: W78C33BP-24/40

−

QFP 44: W78C33BF-24/40

−

TQFP 44: W78C33BM-24/40

-1-

Publication Release Date: June 1998

Revision A1

Preliminary W78C33B

FUNCTIONAL DESCRIPTION

The W78C33B architecture consists of a core controller surrounded by various registers, five general

purpose I/O ports, 256 bytes of RAM, three timer/counters, and a serial port. The processor supports

111 different instruction and references both a 64K program address space and a 64K data storage

space.

Timers 0, 1, and 2

Timers 0, 1, and 2 each consist of two 8-bit data registers. These are called TL0 and TH0 for Timer 0,

TL1 and TH1 for Timer 1, and TL2 and TH2 for Timer 2. The TCON and TMOD registers provide

control functions for timers 0, 1. The T2CON register provides control functions for Timer 2. RCAP2H

and RCAP2L are used as reload/capture registers for Timer 2.

The operations of Timer 0 and Timer 1 are the same as in the W78C31. Timer 2 is a special feature

of the W78C33B: it is a 16-bit timer/counter that is configured and controlled by the T2CON register.

Like Timers 0 and 1, Timer 2 can operate as either an external event counter or as an internal timer,

depending on the setting of bit C/T2 in T2CON. Timer 2 has three operating modes: capture, auto-

reload, and baud rate generator. The clock speed at capture or auto-reload mode is the same as that

of Timers 0 and 1.

Clock

The W78C33B is designed to be used with either a crystal oscillator or an external clock. Internally,

the clock is divided by two before it is used. This makes the W78C33B relatively insensitive to duty

cycle variations in the clock.

Crystal Oscillator

The W78C33B incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must be

connected across pins XTAL1 and XTAL2. In addition, a load capacitor must be connected from each

pin to ground, and a resistor must also be connected from XTAL1 to XTAL2 to provide a DC bias

when the crystal frequency is above 24 MHz.

External Clock

An external clock should be connected to pin XTAL1. Pin XTAL2 should be left unconnected. The

XTAL1 input is a CMOS-type input, as required by the crystal oscillator. As a result, the external clock

signal should have an input one level of greater than 3.5 volts.

Power Management

Idle Mode

The idle mode is entered by setting the IDL bit in the PCON register. In the idle mode, the internal

clock to the processor is stopped. The peripherals and the interrupt logic continue to be clocked. The

processor will exit idle mode when either an interrupt or a reset occurs.

Power-down Mode

When the PD bit of the PCON register is set, the processor enters the power-down mode. In this

mode all of the clocks, including the oscillator are stopped. The only way to exit power-down mode is

by a reset.

-5-

Publication Release Date: June 1998

Revision A1

W78C33BM-24 Related Products

	W78C33BM-24	W78C33BP-40	W78C33BM-40	W78C33BF-40	W78C33BF-24	W78C33B-40	W78C33B-24	W78C33B
Description	8-BIT MICROCONTROLLER	8-BIT MICROCONTROLLER	8-BIT MICROCONTROLLER	8-BIT MICROCONTROLLER	8-BIT MICROCONTROLLER	8-BIT MICROCONTROLLER	8-BIT MICROCONTROLLER	8-BIT MICROCONTROLLER

Recommended Resources

Interface circuit between AD574A and PC bus

Circuit diagram of high-power triode (Darlington tube) for output tube

Fahrenheit thermometer circuit

Infrared thermometer circuit diagram

UHF prestage circuit with n-type regulation network

Internal circuit and pins of μPC1373H and LA7224

Based in Chengdu, recruitment position: mid-level or senior hardware engineer: Recruitment position : Intermediate or senior hardware engineer ; Job Description: 1. Complete the design of electrical subsystem according to product requirements and system solutions; 2. Design circ...; mgstanley Recruitment

The biggest pain point of WiFi in the past has finally been solved by WiFi7. . .: I have to mention the guy who named the 802.11ax protocol WiFi 6.Must be a genius!!!Because if it weren't for those people who tinker with these things every day.Who knows what 802.11n, 802.11ac, 802....; btty038 RF/Wirelessly

Recommended domestic positive-to-negative LDO chips: Domestic positive-to-negative LDO chip recommendation, similar to ICL7660 in function...; 1nnocent Power technology

How to generate coe file using ise software: It is generated by ise software, not by editing it yourself. Like in quartus ii, you can fill in any data yourself....; 郝旭帅 FPGA/CPLD

Using SPMC75 to realize SVPWM synthesis: Abstract: This paper mainly introduces the method of generating SVPWM using SPMC75 microcontroller. Keywords: SPMC75, SVPWM, SPWM 1.1 Introduction 　　With the development of computer technology and pow...; rain MCU

Temperature transmitter hardware framework and schematic diagram: [i=s]This post was last edited by Blue Angel on 2022-9-14 22:17[/i]1. Hardware architecture: I recently read the ADUCM360 data sheet in detail and found that some IO ports of the MCU can be configured...; 蓝色天使 DigiKey Technology Zone

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components