notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the
latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc.
Rev. A
06/01/09
1
IS43R16800CC
PIN CONFIGURATIONS
66 pin TSOP - Type II for x16
V
DD
DQ0
V
DD
Q
DQ1
DQ2
V
SS
Q
DQ3
DQ4
V
DD
Q
DQ5
DQ6
V
SS
Q
DQ7
NC
V
DDQ
LDQS
NC
VDD
NC
LDM
WE
CAS
RAS
CS
NC
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
V
SS
DQ15
V
SS
Q
DQ14
DQ13
V
DD
Q
DQ12
DQ11
V
SS
Q
DQ10
DQ9
V
DD
Q
DQ8
NC
V
SSQ
UDQS
NC
VREF
VSS
UDM
CK
CK
CKE
NC
NC
A11
A9
A8
A7
A6
A5
A4
VSS
PIN DESCRIPTION:
A0-A11
A0-A8
BA0, BA1
DQ0 – DQ15
CLK,
CLK
CKE
CS
CAS
RAS
Row Address Input
Column Address Input
Bank Select Address
Data I/O
System Clock Input
Clock Enable
Chip Select
Column Address Strobe
Command
Row Address Strobe
Command
WE
LDM, UDM
LDQS, UDQS
VDD
VDDQ
VSS
VSSQ
VREF
NC
Write Enable
Data Write Mask
Data Strobe
Power
Power Supply for I/O Pins
Ground
Ground for I/O Pins
SSTL_2 reference voltage
No Connection
2
Integrated Silicon Solution, Inc.
Rev. A
06/01/09
Zentel Electronics Corporation
I
IS43R16800CC
I
PIN FUNCTION
SYMBOL
Preliminary
A3S56D30/40ETP
256M Double Data Rate Synchronous DRAM
TYPE
DESCRIPTION
Clock: CLK and /CLK are differential clock inputs. All address and control
input signals are sampled on the crossing of the positive edge of CLK and
negative edge of /CLK. Output (read) data is referenced to the crossings of
CLK and /CLK (both directions of crossing).
Clock Enable: CKE controls internal clock. When CKE is low, internal clock
for the following cycle is ceased. CKE is also used to select auto / self refresh.
After self refresh mode is started, CKE becomes asynchronous input. Self refresh
is maintained as long as CKE is low.
Chip Select: When /CS is high, any command means No Operation.
Combination of /RAS, /CAS, /WE defines basic commands.
A0-11 specify the Row / Column Address in conjunction with BA0,1. The
Row Address is specified by A0-11. The Column Address is specified by
A0-8.
A10 is also used to indicate precharge
option. When A10 is high at a read / write,
an auto precharge is
performed. When A10 is high at a precharge command,
all banks are
precharged.
CLK, /CLK
Input
CKE
Input
/CS
/RAS, /CAS, /WE
Input
Input
A0-11
Input
BA0,1
D
DQ0-15
Input
Bank Address: BA0,1 specifies one of four banks to which a command is
applied. BA0,1 must be set with ACT, PRE, READ, WRITE commands.
Data Input/Output: Data bus
Data Strobe: Output with read data, input with write data. Edge-aligned
with read data, centered in write data. Used to capture write data.
For the x16, LDQS corresponds to the data on DQ0-DQ7; UDQS
correspond to the data on DQ8-DQ15
Input Data Mask: DM is an input mask signal for write data. Input data
is masked when DM is sampled HIGH along with that input data
during a WRITE access. DM is sampled on both edges of DQS.
Although DM pins are input only, the DM loading matches the DQ
and DQS loading. For the x16, LDM corresponds to the data on DQ0-DQ7;
UDM corresponds to the data on DQ8-DQ15.
Power Supply for the memory array and peripheral circuitry.
V
DDQ,
and
V
SSQ
are supplied to the Output Buffers only.
Input / Output
D
UDQS, LDQS
Input / Output
D
UDM, LDM
Input
V
DD
,
V
SS
V
DDQ,
V
SSQ
Power Supply
Power Supply
Input
Vref
SSTL_2 reference voltage.
Integrated Silicon Solution, Inc.
Rev.
A
06/01/09
DDR SDRAM (Rev.1.1)
3
IS43R16800CC
DQ 0 - 15
UDQS, LD QS
BLOCK DIAGRAM x16
DLL
I/O B uffer
DQ S Buffer
Memory
Array
Bank #0
Memory
Array
Ba nk #1
Memory
Array
Ba nk #2
Memory
Array
Ba nk #3
Mode Re gister
Control C ircu itry
Addres s B uffer
Cl ock B uffer
A0-11
BA 0,1
CLK
/CLK
CKE
Control Signal B uffer
/CS /RAS /CAS
/WE
UDM ,
LD M
4
Integrated Silicon Solution, Inc.
Rev.
A
06/01/09
Zentel Electronics Corporation
IS43R16800CC
I
Preliminary
A3S56D30/40ETP
256M Double Data Rate Synchronous DRAM
ISSI's
128-Mbit
DDR SDRAM
provides basic functions, bank (row) activate, burst read / write, bank
(row) precharge, and auto / self refresh. Each command is defined by control signals of /RAS,
/CAS and /WE at CLK rising edge. In addition to 3 signals, /CS , CKE and A10 are used as chip
select, refresh option, and precharge option, respectively. To know the detailed definition of
commands, please see the command truth table.
/CLK
CLK
/CS
/RAS
/CAS
/WE
CKE
A10
Chip Select : L=select, H=deselect
Command
Command
Command
Refresh Option @refresh command
Precharge Option @precharge or read/write command
define basic commands
BASIC FUNCTIONS
Activate (ACT) [/RAS =L, /CAS =/WE =H]
ACT command activates a row in an idle bank indicated by BA.
Read (READ) [/RAS =H, /CAS =L, /WE =H]
READ command starts burst read from the active bank indicated by BA. First output data appears after
/CAS latency. When A10 =H at this command, the bank is deactivated after the burst read (auto-
precharge,
READA)
Write (WRITE) [/RAS =H, /CAS =/WE =L]
WRITE command starts burst write to the active bank indicated by BA. Total data length to be written
is set by burst length. When A10 =H at this command, the bank is deactivated after the burst write
(auto-precharge,
WRITEA)
Precharge (PRE) [/RAS =L, /CAS =H, /WE =L]
PRE command deactivates the active bank indicated by BA. This command also terminates burst read
/write operation. When A10 =H at this command, all banks are deactivated (precharge all,
PREA
).
Auto-Refresh (REFA) [/RAS =/CAS =L, /WE =CKE =H]
REFA command starts auto-refresh cycle. Refresh address including bank address are generated
internally. After this command, the banks are precharged automatically.
Live Replay: Protecting Clean Water Sources - ADI Water Quality Monitoring Solution : https://training.eeworld.com.cn/course/5836With the country's investment in environmental protection, the demand f...
[size=4][color=#000000][backcolor=white] 5G-related communication capabilities, spectrum demarcation, operator licenses and other related information are flying all over the sky, giving people a feeli...
Before learning how to use an oscilloscope to reduce noise, let's first understand where the oscilloscope noise comes from.
Many people who have just switched from analog oscilloscopes to digital osci...
As the title says, I know that zone 7 in our community is the gas alarm zone, zone 8 is the emergency help button, and I don't know the others. I hope an expert can answer what zones 1-6 are....
The NXP Rapid IoT source code is very rich. Although I know that FreeRTOS is used, the code nesting is extremely complex, which makes it difficult to analyze. So if you want to use FreeRTOS's own vTas...
As of the end of April, the 2022 annual reports of 36 listed companies in Guizhou have been disclosed, and they have achieved good results in profitability, asset quality, financing scale, etc. The to...[Details]
ADC driver design
ADC: Analog-to-digital converter.
A device that converts analog signals into digital signals;
DAC: Digital to Analog Converter.
A device that converts di...[Details]
The soft starter has many functions such as soft start, soft stop, pump control, timed low-speed operation, etc. Therefore, it has incomparable advantages over traditional step-down starters in the...[Details]
Microchip introduces new products in the maXTouch® touch screen controller series
Providing more security features to touchscreen payment systems
ATMXT2952TD 2.0 touch con...[Details]
Famous humanoid
robot
manufacturer Agility Robotics recently announced that veteran technology executive Peggy Johnson will serve as the company's CEO, replacing co-founder Damion Shelton. ...[Details]
Our world is taking great strides towards science fiction.
In the past few months, the emergence of ChatGPT has set off a wave of artificial intelligence craze. This powerful chatbot
h...[Details]
A variable frequency drive (VFD) is an electronic device used to control the speed of a motor. It achieves speed regulation of the motor by changing the frequency and voltage of the motor power sup...[Details]
Huawei
Analysis of Tuling chassis technology
Starting from the 863 Plan of the 15th Five-Year Plan, China's
new energy vehicles
have been developing rapidly for mo...[Details]
Is the 4680 large cylindrical battery "difficult to deliver" again? According to Gasgoo reports, on May 10, Panasonic stated that it would postpone the commercial production of Tesla 4680 batteries...[Details]
Where does the electric energy of new energy vehicle motors come from? The electric energy of motors is converted by the braking energy feedback system and fed back to the AC power grid for use by ...[Details]
VS919, the single-chip smart driving chip for Weijing Yuxing
Automotive-grade chips
Unique advantages:
The VS919 series chips officially released by Wei...[Details]
Dylan Patel, chief analyst at consulting firm SemiAnalysis, cited an informant who revealed that Intel (Intel) is preparing to cut the budget by 10% and lay off up to 20% of its two major divisions r...[Details]
There are many types of automotive sensors, and automotive gas sensors are the most important component. According to incomplete statistics, gas sensors account for more than 50% of the sensors use...[Details]
Intelligent driving is the latest technology and marketing front for new energy vehicles, but it is also filled with uncertainty and other competitive smoke.
On August 5, Reuters reporte...[Details]
I. Introduction Digital multimeter: A multi-purpose electronic measuring instrument that generally includes functions such as an ammeter, voltmeter, and ohmmeter. It is sometimes also called a multim...[Details]