85°C ± 2°C, 85%±5%RH, 1000 hours; 1.5 hr ON, 0.5 hr OFF cycle
85°C ± 2°C, 3000 hours, 1.5 hr ON, 0.5 hr OFF cycle
+155°C, 1000 hours
* Depends on resistance value, please contact KOA Speer for details.
Precautions for Use
• The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts
absorb on the top tapes to cause a failure in the mounting and the parts are destructed by static electricity (1J, 2A, 2B, 2E: 1kV and more, 1E: 0.5kV and more at Human
Body Model 100pF, 1.5kΩ) to change the resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged
on the tapes. Similarly, care should be given not to apply the excessive static electricity when mounting on the boards.
• Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc.
The flux may contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na＋), chlorine (Cl−) etc. Therefore these
kinds of ionic substances may induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since
lead free solder contains ionic substances. Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
• Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk
may happen that the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of
protecting coat may be dropped down. Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
• Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. 5~35°C/35~75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like
hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
●
The upper electrodes could be peeled off when a heat-resistant masking tape is attached to the mounted chip resistors and then detached from them. It is confirmed that
the adhesiveness gets stronger due to the exposure to heat under mounting. Accordingly, we recommend the use of masking tape be refrained. If the use of heat-resistant
masking tape is unavoidable, please make sure that the adhesives on the tape do not directly come in contact with the product.
For Surface Temperature Rise Graph see Environmental Applications. Additional environmental applications can also be found at www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
11/06/17
KOA Speer Electronics, Inc.
• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
For any RF chip, frequency accuracy is the most important indicator of its RF performance. It may cause problems such as failure to connect, poor transmission indicators, and poor receiving sensitivit...
[i=s]This post was last edited by FantasyTG on 2020-8-18 10:45[/i]Importing 3D PCB error as shown belowDetails: Company version AD6 (older versionAccording to the online suggestion, import the 3D mode...
Read a long data from RAM address 0x0200 and burn it into Flash at address 0x1800.Code:#include“io430.h”void main（void）{//Initialize the pointer of RAM information segmentunsigned long * RAM_ptr = （un...
The following description takes CC2640R2F as an example. There are two low-power modes: 1. Power-down mode (shutdown), 2. Sleep mode (sleep or standby)
API Description
1. Sleep mode
This is the Standb...
The possible causes of RF interference are increasing, some are obvious and easy to track, while others are very subtle and difficult to identify. Although careful design of base stations can provide ...
Jiwei.com reported on October 23 that Huawei held a global new product online conference yesterday and launched the new generation flagship Huawei Mate 40 series. Yu Chengdong said that four years ag...[Details]
The tube amplifiers made by many friends are not ideal. There are two main reasons for this:
1. Since the knowledge of tube circuits and their applications was only available in textbooks in the 1...[Details]
Based on STM32 and STM8 processors, multiple functional modules of the universal testing machine were designed. In order to improve the acquisition accuracy and speed of small signals, a hybrid p...[Details]
200. L uses enameled wire with a diameter of 1 mm, wound 4 times, and the hollow diameter is about 5 mm. The antenna can be made of multiple strands of thin wire, about 50 cm long. The micropho...[Details]
"At present, new energy vehicles have entered a new stage of accelerated development, facing major opportunities as well as many challenges in technology and market." On September 16, the 2021 World ...[Details]
Researchers have developed a metal-free jelly-like material that is as soft and tough as biological tissue and can conduct electricity like traditional metals. Image credit: Massachusetts I...[Details]
The diode test shown in the figure is simple and easy to perform, and the test is convenient and fast.
In the figure, T is a 220/3V, 2W transformer; VD1 and VD2 are 2CP10 type rectifier diodes, LE...[Details]
Japan's Panasonic Corp. plans to reduce its heavy reliance on Tesla Inc. by producing batteries that can be used in other brands of electric vehicles, outgoing CEO Kazuhiro Tsuga said. Tsuga's comm...[Details]
Crystal/Ceramic Oscillator Basic Circuit
Below are two application circuits for crystal/ceramic oscillators.
Description 1. The internal bias resistor RINB is used to generate the operating po...[Details]
MCU serial communication is a very useful function of MCU. It can communicate and exchange data with computers and other MCUs to achieve certain effects. Recently, we made a program: using MCU seri...[Details]
Times have changed and floppy drives are no longer useful, but the motor inside is quite interesting, so I took it out and studied it.
CODE:
/*Use mega32 three port lines to drive the floppy d...[Details]
0 Introduction
Against the backdrop of increasing global environmental pollution and fossil energy shortages, the development of new energy vehicles represented by pure electric vehicles has a...[Details]
Elon Musk's brain chip startup Neuralink is preparing to launch human clinical trials to implant brain chips into the human body. According to Neuralink, its goal is to build a "brain-computer inte...[Details]
Abstract: This paper
introduces the design overview of the textile digital printing machine and the characteristics of the USB controller CY7C68013A. It also describes the design of FPGA acce...[Details]
The so-called level refers to the logarithm of the ratio of two powers or voltages. Sometimes it can also be used to express the logarithm of the ratio of two currents. The unit of level is decibel...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
