The ICM7373, ICM7353 and ICM7333 are Dual 12-Bit, 10-
Bit and 8-Bit Rail-to-Rail voltage output DACs respectively,
with guaranteed monotonic behavior. These DACs are
available in 16 Lead QSOP package. They include
adjustable output gain for ease of use and flexibility. The
reference output is available on a separate pin and can be
used to drive external loads. The operating supply range is
2.7V to 5.5V.
The input interface is an easy to use three-wire SPI/QSPI
and Microwire compatible interface. The DAC has a
double buffered digital input. And there is a serial data
output port to allow daisy-chaining applications.
BLOCK DIAGRAM
REFB
REFA
ICM7373/7353/7333
INPUT AND DAC LATCH
DAC A
+
-
INPUT AND DAC LATCH
DAC B
VOA
FBA
+
-
VOB
FBB
REFERENCE
REFOUT
INPUT CONTROL LOGIC, REGISTERS AND LATCHES
SDO
SDI
SCK
CS
CLR
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
1
ICmic
PACKAGE
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
16 Lead QSOP
AGND
VOA
FBA
REFA
CLR
CS
SDI
SCK
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VDD
VOB
FBB
REFB
N/C
REFOUT
SDO
DGND
TOP VIEW
PIN DESCRIPTION (16 Lead QSOP)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Name
AGND
VOA
FBA
REFA
CLR
CS
SDI
SCK
DGND
SDO
REFOUT
N/C
REFB
FBB
VOB
VDD
I/O
I
O
I
I
I
I
I
I
I
O
O
-
I
I
O
I
Analog Ground
DAC A Output Voltage
Description
Inverting Input of The Output Amplifier DAC A. Output Amplifier Feedback Input.
Reference Voltage Input for DAC A
Active Low Clear Input (CMOS). Resets All Registers to Zero. DAC outputs go to 0 V
Active Low Chip Select (CMOS)
Serial Data Input (CMOS)
Serial Clock Input (CMOS)
Digital Ground
Serial Data Output
Reference Output
No Connection
Reference Voltage Input for DAC B
Inverting Input of The Output Amplifier DAC B. Output Amplifier Feedback Input.
DAC B Output Voltage
Supply Voltage
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
2
ICmic
Symbol
V
DD
I
IN
V
IN_
V
IN_REF
T
STG
T
SOL
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
ABSOLUTE MAXIMUM RATING
Parameter
Supply Voltage
Input Current
Digital Input Voltage (SCK, SDI, CS , CLR )
Reference Input Voltage
Storage Temperature
Soldering Temperature
Value
-0.3 to 7.0
+/- 25.0
-0.3 to 7.0
-0.3 to 7.0
-65 to +150
300
Unit
V
mA
V
V
o
o
C
C
Note:
Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
ORDERING INFORMATION
Part
ICM7373
ICM7353
ICM7333
Operating Temperature Range
-40
o
C to 85
o
C
-40 C to 85 C
-40 C to 85 C
o
o
o
o
Package
16-Pin QSOP
16-Pin QSOP
16-Pin QSOP
DC ELECTRICAL CHARACTERISTICS
(V
DD
= 2.7V to 5.5V; V
OUT
unloaded; all specifications T
MIN
to T
MAX
unless otherwise noted)
Symbol
DC PERFORMANCE
ICM7373
N
DNL
INL
ICM7353
N
DNL
INL
ICM7333
N
DNL
INL
Resolution
Differential Nonlinearity
Integral Nonlinearity
(Notes 1 & 3)
(Notes 1 & 3)
8
0.05
0.25
+1.0
+0.75
Bits
LSB
LSB
% of
FS
mV
Resolution
Differential Nonlinearity
Integral Nonlinearity
(Notes 1 & 3)
(Notes 1 & 3)
10
0.1
1.0
+1.0
+3.0
Bits
LSB
LSB
Resolution
Differential Nonlinearity
Integral Nonlinearity
(Notes 1 & 3)
(Notes 1 & 3)
12
0.4
4.0
+1.0
+12.0
Bits
LSB
LSB
Parameter
Test Conditions
Min
Typ
Max
Unit
GE
OE
Gain Error
Offset Error
+0.5
+25
POWER REQUIREMENTS
V
DD
I
DD
Supply Voltage
Supply Current
2.7
0.6
3.6
1.5
V
mA
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
3
ICmic
Symbol
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
Parameter
Test Conditions
Min
Typ
Max
Unit
OUTPUT CHARACTERISTICS
Output Voltage Range
VO
SC
R
OUT
Short Circuit Current
Amp Output Impedance
Output Line Regulation
LOGIC INPUTS
V
IH
V
IL
Digital Input High
Digital Input Low
Digital Input Leakage
REFERENCE
V
REFOUT
Reference Output
Reference Output Line
Regulation
1.2
1.25
0.8
1.3
4.0
V
mV/V
(Note 2)
(Note 2)
2.4
0.8
5
V
V
µΑ
At Mid-scale (Note 2)
At 0-scale (Note 2)
V
DD
=2.7 to 3.6 V
(Note 3)
0
60
1.0
100
0.4
V
DD
150
5.0
200
3.0
V
mA
Ω
Ω
mV/V
AC ELECTRICAL CHARACTERISTICS
(V
DD
= 2.7V to 5.5V; V
OUT
unloaded; all specifications T
MIN
to T
MAX
unless otherwise noted)
Symbol
SR
Parameter
Slew Rate
Settling Time
Mid-scale Transition Glitch
Energy
Test Conditions
Min
Typ
2
8
40
Max
Unit
V/µs
µs
nV-S
Note 1:
Note 2:
Note 3:
Linearity is defined from code 64 to 4095 (ICM7373)
Linearity is defined from code 16 to 1023 (ICM7353)
Linearity is defined from code 4 to 255 (ICM7333)
Guaranteed by design; not tested in production
See Applications Information
TIMING CHARACTERISTICS
(V
DD
= 2.7V to 5.5V; all specifications T
MIN
to T
MAX
unless otherwise noted)
Symbol
t
1
t
2
t
3
t
4
t
5
t
6
Parameter
SCK Cycle Time
Data Setup Time
Data Hold Time
SCK Falling edge to CS Rising Edge
CS Falling Edge to SCK Rising Edge
CS Pulse Width
Test
Conditions
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
Min
30
10
10
0
15
20
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
4
ICmic
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
t
6
CS
t
1
t
4
t
5
SCK
t
2
SDI
C3
D0
t
3
DAC INPUT WORD
Figure 1.
Serial Interface Timing Diagram
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
I'm currently researching CubeMX and USB.
I opened STM32CubeMX and saw the picture above. I don't know what USB_OTG_FS and USB_OTG_HS mean?
I couldn't find it on Baidu either.
Is it all related to the...
Since we need to write TM1680, write commands and write data, we need to use the I2C of CC2541, which has hardware I2C.
tm1680.c:
#include "tm1680.h"
//TM1680 sends configuration first, then data.void...
The ADC evaluation board below comes with a PHI EVM Controller. I don't know where to get the information.
After ADS8588S EVM.exe is connected to a computer, can it realize the synchronous acquisition...
Loto practical experience ( 8 ) Application case of loto oscilloscope in the maintenance of LED desk lamp dimming problem
A customer recently felt that his LED desk lamp was too flashy .So I took it a...
[b][size=5]LED Lighting Test[/size][/b] Let's start with the simplest one, the classic Hello World. I put an Interval and an RGB LED. Through the Toggle RedLED event, the RGB LED in the upper left cor...
[url=https://www.eeworld.com.cn/huodong/TI_20190404/index.html]Today at 10:00 am, there will be a prize live broadcast: [Introduction to the industrial open source platform based on TI Sitara AM5708][...
1 I2C bus characteristics
The main advantages of the I2C bus are its simplicity and effectiveness. Since the interface is directly on the components, the I2C bus takes up very little space, re...[Details]
As the ease of use and performance of very low-power sensors, microcontrollers, and radio frequency (RF) transceivers continue to improve, wireless sensor networks powered exclusively or supplemen...[Details]
Abstract: The public telephone network technology is mature and covers a wide range. It is a very effective method to use the existing public telephone network to realize remote communication be...[Details]
The following startup code is extracted from "ARM Embedded System Experiment Tutorial (I)".
1; Start the file, initialize the running environment of the C program, and then enter the C program code....[Details]
We adopt a single full-bridge LLC topology to obtain high efficiency and reasonable cost. It consists of U60 and Q60, Q62, Q70, Q72, etc. NCV4390 (U60) is a current mode advanced LLC controller...[Details]
What are bit and sbit? What's the difference between them? When I first learned about the 51 microcontroller, I was confused when I saw these two things. The first reaction in my mind was, what the h...[Details]
Vehicle restriction is an effective measure to solve urban traffic congestion. It has been proven in practice and its effect has been recognized by the society. Most cities use the scheme of restri...[Details]
As the speed of real-time signal processing continues to increase, the clock frequency of digital circuit systems also increases. At the same time, the improvement of semiconductor technology has also...[Details]
"If the IC design industry needs to work hard for another 10 years, I think the manufacturing industry will need at least 20 to 30 years, and 30 to 50 years is normal." On December 10, Peng Jin, seni...[Details]
OFweek Cup 2022 China
Robot
Industry Annual Awards (abbreviated as OFweek Robot Awards 2022) is jointly organized by OFweek, China's high-tech industry portal, and its authoritative robot p...[Details]
Unlike smartphones, Samsung has not made much progress in the field of smart speakers. Although Samsung announced the Samsung Galaxy Home artificial intelligence speaker as early as the Samsung...[Details]
Take MSP430F2274 as an example. The assembly implementation uses IAR assembly, and the CCE assembly implementation can be slightly modified.
1. The watchdog has three working modes: stop mode, time...[Details]
Smart battery box
The appearance and internal structure of the homemade battery box introduced here are shown in Figure 6-21. It can hold eight No. 1 batteries, and can lead ou...[Details]
Frequency measurement is often used in the field of electronic design and measurement, so the study of frequency measurement methods is of great significance in practical engineering applications. ...[Details]
Foreign media reported that Parker Hannifin, a motion and control technology company, launched the LORD Force Feedback Device (FFD). This is an integrated solution that combines a steering sensor, ...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
