The ICM7373, ICM7353 and ICM7333 are Dual 12-Bit, 10-
Bit and 8-Bit Rail-to-Rail voltage output DACs respectively,
with guaranteed monotonic behavior. These DACs are
available in 16 Lead QSOP package. They include
adjustable output gain for ease of use and flexibility. The
reference output is available on a separate pin and can be
used to drive external loads. The operating supply range is
2.7V to 5.5V.
The input interface is an easy to use three-wire SPI/QSPI
and Microwire compatible interface. The DAC has a
double buffered digital input. And there is a serial data
output port to allow daisy-chaining applications.
BLOCK DIAGRAM
REFB
REFA
ICM7373/7353/7333
INPUT AND DAC LATCH
DAC A
+
-
INPUT AND DAC LATCH
DAC B
VOA
FBA
+
-
VOB
FBB
REFERENCE
REFOUT
INPUT CONTROL LOGIC, REGISTERS AND LATCHES
SDO
SDI
SCK
CS
CLR
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
1
ICmic
PACKAGE
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
16 Lead QSOP
AGND
VOA
FBA
REFA
CLR
CS
SDI
SCK
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VDD
VOB
FBB
REFB
N/C
REFOUT
SDO
DGND
TOP VIEW
PIN DESCRIPTION (16 Lead QSOP)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Name
AGND
VOA
FBA
REFA
CLR
CS
SDI
SCK
DGND
SDO
REFOUT
N/C
REFB
FBB
VOB
VDD
I/O
I
O
I
I
I
I
I
I
I
O
O
-
I
I
O
I
Analog Ground
DAC A Output Voltage
Description
Inverting Input of The Output Amplifier DAC A. Output Amplifier Feedback Input.
Reference Voltage Input for DAC A
Active Low Clear Input (CMOS). Resets All Registers to Zero. DAC outputs go to 0 V
Active Low Chip Select (CMOS)
Serial Data Input (CMOS)
Serial Clock Input (CMOS)
Digital Ground
Serial Data Output
Reference Output
No Connection
Reference Voltage Input for DAC B
Inverting Input of The Output Amplifier DAC B. Output Amplifier Feedback Input.
DAC B Output Voltage
Supply Voltage
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
2
ICmic
Symbol
V
DD
I
IN
V
IN_
V
IN_REF
T
STG
T
SOL
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
ABSOLUTE MAXIMUM RATING
Parameter
Supply Voltage
Input Current
Digital Input Voltage (SCK, SDI, CS , CLR )
Reference Input Voltage
Storage Temperature
Soldering Temperature
Value
-0.3 to 7.0
+/- 25.0
-0.3 to 7.0
-0.3 to 7.0
-65 to +150
300
Unit
V
mA
V
V
o
o
C
C
Note:
Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
ORDERING INFORMATION
Part
ICM7373
ICM7353
ICM7333
Operating Temperature Range
-40
o
C to 85
o
C
-40 C to 85 C
-40 C to 85 C
o
o
o
o
Package
16-Pin QSOP
16-Pin QSOP
16-Pin QSOP
DC ELECTRICAL CHARACTERISTICS
(V
DD
= 2.7V to 5.5V; V
OUT
unloaded; all specifications T
MIN
to T
MAX
unless otherwise noted)
Symbol
DC PERFORMANCE
ICM7373
N
DNL
INL
ICM7353
N
DNL
INL
ICM7333
N
DNL
INL
Resolution
Differential Nonlinearity
Integral Nonlinearity
(Notes 1 & 3)
(Notes 1 & 3)
8
0.05
0.25
+1.0
+0.75
Bits
LSB
LSB
% of
FS
mV
Resolution
Differential Nonlinearity
Integral Nonlinearity
(Notes 1 & 3)
(Notes 1 & 3)
10
0.1
1.0
+1.0
+3.0
Bits
LSB
LSB
Resolution
Differential Nonlinearity
Integral Nonlinearity
(Notes 1 & 3)
(Notes 1 & 3)
12
0.4
4.0
+1.0
+12.0
Bits
LSB
LSB
Parameter
Test Conditions
Min
Typ
Max
Unit
GE
OE
Gain Error
Offset Error
+0.5
+25
POWER REQUIREMENTS
V
DD
I
DD
Supply Voltage
Supply Current
2.7
0.6
3.6
1.5
V
mA
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
3
ICmic
Symbol
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
Parameter
Test Conditions
Min
Typ
Max
Unit
OUTPUT CHARACTERISTICS
Output Voltage Range
VO
SC
R
OUT
Short Circuit Current
Amp Output Impedance
Output Line Regulation
LOGIC INPUTS
V
IH
V
IL
Digital Input High
Digital Input Low
Digital Input Leakage
REFERENCE
V
REFOUT
Reference Output
Reference Output Line
Regulation
1.2
1.25
0.8
1.3
4.0
V
mV/V
(Note 2)
(Note 2)
2.4
0.8
5
V
V
µΑ
At Mid-scale (Note 2)
At 0-scale (Note 2)
V
DD
=2.7 to 3.6 V
(Note 3)
0
60
1.0
100
0.4
V
DD
150
5.0
200
3.0
V
mA
Ω
Ω
mV/V
AC ELECTRICAL CHARACTERISTICS
(V
DD
= 2.7V to 5.5V; V
OUT
unloaded; all specifications T
MIN
to T
MAX
unless otherwise noted)
Symbol
SR
Parameter
Slew Rate
Settling Time
Mid-scale Transition Glitch
Energy
Test Conditions
Min
Typ
2
8
40
Max
Unit
V/µs
µs
nV-S
Note 1:
Note 2:
Note 3:
Linearity is defined from code 64 to 4095 (ICM7373)
Linearity is defined from code 16 to 1023 (ICM7353)
Linearity is defined from code 4 to 255 (ICM7333)
Guaranteed by design; not tested in production
See Applications Information
TIMING CHARACTERISTICS
(V
DD
= 2.7V to 5.5V; all specifications T
MIN
to T
MAX
unless otherwise noted)
Symbol
t
1
t
2
t
3
t
4
t
5
t
6
Parameter
SCK Cycle Time
Data Setup Time
Data Hold Time
SCK Falling edge to CS Rising Edge
CS Falling Edge to SCK Rising Edge
CS Pulse Width
Test
Conditions
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
Min
30
10
10
0
15
20
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
4
ICmic
IC MICROSYSTEMS
Dual 12/10/8-Bit Voltage Output DACs
Serial Interface with Adjustable Output Gain
ICM7373/7353/7333
t
6
CS
t
1
t
4
t
5
SCK
t
2
SDI
C3
D0
t
3
DAC INPUT WORD
Figure 1.
Serial Interface Timing Diagram
Rev. A1
ICmic reserves the right to change the specifications without prior notice.
Recently, the USB PD3.0 fast charging standard has been upgraded. The new USB PD3.1 fast charging standard will support a maximum voltage output of 48V, and the charging power will be increased to 240...
1. IntroductionBefore I really understood RISC-V, I actually only saw articles about it on some embedded public accounts that I followed, and I saw it many times. It can be seen that it is really popu...
The serial dot matrix module is a dot matrix display module with MAX7219 as the control chip. In the case of single-stage use, one MAX7219 can control an 8*8 dot matrix display block. If the cascade m...
Huawei's Hongmeng 2.0 was released yesterday. If you missed it, you can check it out here: Born for the Internet of Everything, China's own mobile phone operating system Hongmeng is released!I woke up...
This manual is divided into three parts: The first part is divided into four chapters, which introduce Cadence cdsSpice, Virtuoso Editing, Diva and Verilog respectively. The second part mainly introdu...
In the name of SOLDER layer, SOLDER means welding. Which guru insisted on translating it into solder mask layer? Please help me explain it. Thank you....
Background The end of the year is approaching, but I can't stop learning. Recently, I have been working on a Nes emulator that can run on a single-chip microcomputer, which is the red and white game ...[Details]
1. Background A user in a certain area reported a variable frequency air conditioner, which would trigger high temperature protection in heating mode at an outdoor ambient temperature of 23°C. The us...[Details]
MIT and MITRE Corporation have demonstrated a scalable, modular hardware platform that integrates thousands of interconnected quantum bits into custom circuits. This quantum system-on-chip (QSoC) a...[Details]
According to foreign media reports, birds have played a significant role in the development of drones over the years. It seems that the extremely agile hummingbird - its ability to hover and make sha...[Details]
Section 001: Auxiliary Line 1_Hardware Knowledge_LED Schematic Diagram Steps to light up the LED: 1. Look at the schematic diagram and determine the pins that control the LED Use the pin output thr...[Details]
#include
#define uchar unsigned char
#define uint unsigned int
#define long unsigned long
//******************* Function declaration***************************
void init_Total(); //Total initializ...[Details]
1. Introduction to SPI interface SPI (Serial Peripheral interface) bus system is a synchronous serial peripheral interface, which enables MCU to communicate with various peripheral devices in seria...[Details]
The resistance value of the resistor connected between SENSE+ and SENSE- is used to adjust the size of the charging current. The resistor is 0.4Ω. Therefore, when the battery voltage is less than 3V,...[Details]
What is a linear regulated power supply?
According to the working state of the regulator tube, we often divide the voltage-regulated power supply into two categories: linear voltage-regula...[Details]
Figure 4: Hierarchical and modular structure of electronic systems in future cars One of the issues with reliability is that it is directly proportional to cost. In the design of automotive safe...[Details]
Guangzhou, July 27, 2023 /PRNewswire/ -- On July 13, Guangzhou. Zou Yun, Director of Wuhan Municipal Transportation Bureau, and his delegation visited the headquarters of Aulton New Energy Group. T...[Details]
Program function, display eight numbers 0, 1, 2, 3, 4, 5, 6, 7 from left to right The program source code is as follows: /* 8 digital tubes display different characters at the same time */ #incl...[Details]
I never really understood the sleep instruction before. Recently, when I was making a smart water meter product, I used an 8-bit microcontroller PIC16F690. When I saw the sleep instruction in the pro...[Details]
T6963C is a liquid crystal display controller that is widely used in instruments. It provides two output modes: text and dot matrix. However, the speed of dot matrix output is much slower than that o...[Details]
LG Energy Solution's performance in the third quarter of 2024 does reflect the weakness in global demand for power batteries.
LG Energy Solution's operating income was 687.78 billion won...[Details]
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
