EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

7108J8WGE3

Description
ROCKER SWITCH, SPDT, LATCHED AND MOMENTARY, 5A, 28VDC, PANEL MOUNT, ROHS COMPLIANT
Categoryswitch    Become warped plate switch   
File Size2MB,22 Pages
ManufacturerC&K
Environmental Compliance  
Download Datasheet Parametric View All

7108J8WGE3 Overview

ROCKER SWITCH, SPDT, LATCHED AND MOMENTARY, 5A, 28VDC, PANEL MOUNT, ROHS COMPLIANT

7108J8WGE3 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerC&K
package instructionROHS COMPLIANT
Reach Compliance Codenot_compliant
ECCN codeEAR99
Actuator colorRED
Actuator length0.371 inch
Actuator materialNYLON
Actuator typeLONG ROCKER
body width6.86 mm
body height9.4 mm
Body length or diameter12.7 mm
center contact materialCOPPER ALLOY
Center contact platingGOLD OVER NICKEL
Contact (AC) maximum rated power R load0.4VA@20VAC
Contact (AC) maximum rated R load5A@120VAC
Maximum contact current (AC)5 A
Maximum contact current (DC)5 A
Contact (DC) maximum rated R load5A@28VDC
Contact functionON-(ON)
Contact resistance0.01 mΩ
Maximum contact voltage (AC)120 V
Maximum contact voltage (DC)28 V
Dielectric withstand voltage1400VAC V
Electrical life40000 Cycle(s)
End contact materialCOIN SILVER
End contact platingGOLD OVER NICKEL
Shell materialSTAINLESS STEEL
Insulation resistance1000000000 Ω
JESD-609 codee4
Installation featuresPANEL MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
sealEPOXY TERMINAL SEALED
surface mountNO
Switch actionLATCHED AND MOMENTARY
switch functionSPDT
Switch typeROCKER SWITCH
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Terminal length0.75 inch
Terminal materialCOPPER ALLOY
Termination typeWIRE WRAP
Base Number Matches1
Foxit Reader cannot add bookmarks?
As shown in Figure 1 below, I want to add a bookmark to the document "Human Body Injury Process.pdf", but I cannot add it; As shown in Figure 2 below, however, the document "TH2826.pdf" can be bookmar...
yhye2world Talking about work
Keeping the right direction: Designing a fault circuit for automotive lighting systems
Indicating system failures to the user is extremely important, especially in automotive lighting. For example, a turn indicator in a car’s taillight indicates that the driver wants to change lanes or ...
alan000345 TI Technology Forum
MSP430-Clock System and GPIO
About the clock system: There are three basic clock input sources: 1-ACLK: Auxiliary clock signal. As shown in the figure, ACLK is obtained by dividing the FLXT1CLK signal by 1/2/4/8 dividers. The BCS...
火辣西米秀 Microcontroller MCU
The first chip university: Nanjing Integrated Circuit University unveiled
On the morning of October 22, the unveiling ceremony of Nanjing Integrated Circuit University and the high-end forum on industrial talent training were held in the new district. Liu Yian, Chairman of ...
eric_wang Talking
How to calculate the current after the voltage is stepped down by the Zener diode?
As shown in the figure, how much current can a 10-ohm resistor theoretically provide?...
vincent.liu Analog electronics
Six tips for PCB layout design to make drawing easier!
Six things to consider when transferring PCB schematics to layout design.All examples mentioned were developed using the Multisim design environment, but the same concepts apply when using different E...
btty038 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号