Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= 5V, V
BATT
= 4.0V, TEMP =
EN
=
CHG
= unconnected, R
ISET
= 2.8kΩ to GND, C
VL
= 0.47µF, BATT bypassed to GND with 1µF,
T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
[i=s]This post was last edited by qwqwqw2088 on 2020-2-11 09:25[/i]1. How to find the right chip reference design and application guide?
Search the chip model on TI's official website and you will be ...
TGF4042 has the function of a noise generator. The manual states that its noise bandwidth is 62.5MHZSet the function generator to noise mode and set it to 200mvPP
Observe the noise and spectrum... Usi...
[i=s]This post was last edited by bqgup on 2020-1-27 10:39[/i]The Internet of Things is very popular nowadays, so let’s get two ESP8266WiFi modules to experience the fun of network control.
one,I use ...
The development goals of the software and information service industry in the 11th Five-Year Plan have been basically determined 2006-6-2 "The 11th Five-Year Plan predicts that the software informati...
Everyone, can the baud rate reach 1M and the transmission distance reach 30M? Can it be achieved in servo products? Is it just laboratory data? Please learn from some experience. Thank you...
As we all know, laser-guided weapons use sensitive specific laser signals as guidance information. In the semi-physical simulation system of laser-guided weapons, target simulation and guidance simul...[Details]
Electronics Fan Network News:
The choice of chip model is the most important for engineers in circuit design. Faced with a wide range of chips on the market, how can they choose the chip that sui...[Details]
CortexM3 is ARM's first microcontroller core based on ARMv7M. It is very different from ARM7 in terms of instruction execution, exception control, clock management, trace debugging and storage protec...[Details]
This solution includes a constant current LED driver. The circuit is connected in single series or parallel. The power efficiency is as high as over 93%, and the power factor is over 90%. Compared wi...[Details]
Following our previous introduction to the implicit interaction of the smart cockpit, today we will share the explicit interaction, which, as the name suggests, is the way in which the driver and pas...[Details]
It can be fully charged in 10 minutes, travel 500 kilometers on a single charge, and minimize safety risks. Toyota said that the company's upcoming solid-state battery will not only change electric v...[Details]
1 Introduction In embedded systems, non-volatile data usually needs to be stored, and the size and type of data vary greatly depending on the system requirements. Therefore, selecting a suitable mem...[Details]
A digital voltmeter is designed using the microcontroller AT89S51 and ADC0809. It can measure DC voltage values between 0 and 5V and has a four-digit display, but uses the least number of compo...[Details]
At present, electronic equipment used in various electronic equipment and systems still uses printed circuit boards as the main assembly method. Practice has proved that even if the circuit schem...[Details]
The interaction between distributed photovoltaic power sources and distribution networks includes the impact of photovoltaic power sources on distribution networks and the impact of distribution ne...[Details]
As a partner of the iCAN National College Students Innovation and Entrepreneurship Competition, TDK has contributed to the discovery and cultivation of a group of outstanding young talents with poten...[Details]
client needs: When customers test motors, they need to detect the current changes when the motor is turned on and off. Generally, the current varies from one ampere to more than ten amperes depending...[Details]
US technology companies have rejected calls from the Trump administration to stop sourcing products from certain Chinese companies because they are concerned that such a policy could violate competit...[Details]
Infineon Technologies Expands EiceDRIVER™ X3 Enhanced and X3 Compact Gate Driver Families with Reinforced Isolation
Recently, Infineon Technologies AG has further expanded its easy-t...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
