input. Also on the chip is the ability to generate a
1.25x clock of the reference plus the reference,
making it possible to generate 20 and 25 MHz
clocks from a 20 MHz crystal.
Features
• Packaged as 8 pin SOIC
• For Fast Ethernet plus SCSI on computer
motherboards
• For AC97 sound on computer motherboards
• Less than 1 ppm synthesis error
• Input crystal frequency of 14.31818 MHz
• Operating voltages of 3.0 to 5.5V
• Available in industrial temperature
• Full CMOS level outputs with 25mA drive
capability at TTL levels
• Ideal for oscillator replacement
• Advanced, low power CMOS process
Block Diagram
VDD GND
2
S1, S0
PLL
Clock
Synthesis
and Control
Circuitry
Crystal
Oscillator
X2
Output
Buffer
CLK1
14.31818MHz
crystal
X1
or clock
Output
Buffer
CLK2
1
Revision 120799
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408)295-9800tel • www.icst.com
MDS 1449B C
MK1449B
Sound/SCSI+Fast Ethernet Clock
Pin Assignment
X1/ICLK
VDD
GND
CLK2
1
2
3
4
8
7
6
5
X2
S1
S0
CLK1
Clock Decoding Table (MHz)
S1
0
0
1
1
S0
0
1
0
1
CLK1
test
40
49.152
x1.25
CLK2
test
25
12.288
Reference
0 = connect directly to ground.
1 = connect directly to VDD.
In the 1,1 mode, crystals or clocks from
5 to 27 MHz can be used as an input.
Pin Descriptions
Number
1
2
3
4
5
6
7
8
Name
X1/ICLK
VDD
GND
CLK2
CLK1
S0
S1
X2
Type
I
P
P
O
O
I
I
O
Description
Crystal connection or clock input. Connect to a 14.31818MHz parallel resonant crystal.
Connect to +3.3V or +5V.
Connect to ground.
Clock 2 output per Table above.
Clock 1 output per Table above.
Select 0 for output clocks. Connect to GND or VDD. See table above.
Select 1 for output clocks. Connect to GND or VDD. See table above.
Crystal connection to a 14.31818 MHz crystal. Leave unconnected for clock input.
Key: I = Input, O = output, P = power supply connection
2
Revision 120799
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408)295-9800tel • www.icst.com
MDS 1449B C
MK1449B
Sound/SCSI+Fast Ethernet Clock
Electrical Specifications
Parameter
Conditions
Minimum
Typical
ABSOLUTE MAXIMUM RATINGS (stresses beyond these can permanently damage the device)
Supply Voltage, VDD
Referenced to GND
Inputs
Referenced to GND
-0.5
Clock Output
Referenced to GND
-0.5
Ambient Operating Temperature
0
Industrial temperature
-40
Soldering Temperature
Max of 10 seconds
Storage temperature
-65
DC CHARACTERISTICS (VDD = 3.3V unless otherwise noted)
Operating Voltage, VDD
3
Input High Voltage, VIH, ICLK only
ICLK (Pin 1)
(VDD/2)+1
VDD/2
Input Low Voltage, VIL, ICLK only
ICLK (Pin 1)
VDD/2
Input High Voltage, VIH
S0, S1
VDD-0.5
Input Low Voltage, VIL
S0, S1
Output High Voltage, VOH
IOH=-25mA
2.4
Output Low Voltage, VOL
IOL=25mA
IDD Operating Supply Current, 5V
No Load, 25, 40MHz
18
IDD Operating Supply Current, 3.3V
No Load, 25, 40MHz
10
Short Circuit Current
CLK output
±70
On-Chip Pull-up Resistor
Pin 7
270
Input Capacitance, S1, S0
Pins 6, 7
4
AC CHARACTERISTICS (VDD = 3.3V unless otherwise noted)
Input Frequency, crystal input
10
14.31818
Input Frequency, clock input
10
14.31818
Output Frequency
VDD = 3.0 to 5.5V
10
Output Clock Rise Time
0.8 to 2.0V
1
Output Clock Fall Time
2.0 to 0.8V
1
Output Clock Duty Cycle
at VDD/2
40
49 to 51
Synthesis error, 25, 40 MHz
Synthesis error, 12.288, 49.152 MHz
Absolute Clock Period Jitter, 20 pF load
Deviation from mean
±240
One Sigma Clock Period Jitter, 20 pF load
100
Maximum
7
VDD+0.5
VDD+0.5
70
85
260
150
5.5
(VDD/2)-1
0.5
0.4
Units
V
V
V
°C
°C
°C
°C
V
V
V
V
V
V
V
mA
mA
mA
kΩ
pF
MHz
MHz
MHz
ns
ns
%
ppm
ppm
ps
ps
27
50
75
60
1
1
3
Revision 120799
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408)295-9800tel • www.icst.com
MDS 1449B C
MK1449B
Sound/SCSI+Fast Ethernet Clock
External Components / Crystal Selection
The MK1449B requires a 0.01µF decoupling capacitor to be connected between VDD and GND. It must
be connected close to the MK1449B to minimize lead inductance. No external power supply filtering is
required for this device. 33Ω terminating resistors can be used next to the CLK pins. The total on-chip
capacitance is approximately 13 pF, so a parallel resonant, fundamental mode crystal should be used. For
crystals with a specified load capacitance greater than 13 pF, crystal capacitors should be connected from
each of the pins X1 and X2 to ground. The value (in pF) of these crystal caps should be = (C
L
-13)*2,
where C
L
is the crystal load capacitance in pF. These external capacitors are only required for applications
where the exact frequency is critical. For a clock input, connect to X1 and leave X2 unconnected (no
capacitors on either).
Package Outline and Package Dimensions
(For current dimensional specifications, see JEDEC pub. no. 95)
8 pin SOIC
E
Pin 1
H
Inches
Symbol Min
Max
A
0.053 0.069
A1
0.004 0.0098
B
0.013 0.020
C
0.0075 0.0098
D
0.189 0.197
E
0.150 0.157
H
0.228 0.244
e
.050 BSC
L
0.016
0.05
Millimeters
Min
Max
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
4.80
5.00
3.80
4.00
5.80
6.20
1.27 BSC
0.41
1.27
D
A1
e
B
C
L
A
Ordering Information
Part/Order Number
MK1449S
MK1449STR
MK1449SI
MK1449SITR
Marking
MK1449S
MK1449S
MK1449SI
MK1449SI
Package
8 pin SOIC
8 pin SOIC on tape and reel
8 pin SOIC
8 pin SOIC on tape and reel
Temperature
0 to 70 °C
0 to 70 °C
-40 to 85 °C
-40 to 85 °C
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Inc. (ICS) assumes no responsibility for either its use or for
the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use
in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements
are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any
ICS product for use in life support devices or critical medical instruments.
4
Revision 120799
Printed 11/15/00
Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408)295-9800tel • www.icst.com
The DLP LightCrafter Display 2000 evaluation module (EVM) is a powerful entry-level platform that enables users to evaluate and design DLP prototypes in applications such as smart home displays, head-...
[color=#000][font="][size=12px]The circuit designed with TPS40057 has 24V input and 11V, 10A output. The peripheral circuit is generated using official software. When the circuit board is powered on w...
GSA confirmed today that there are now 153 operators in 64 countries/regions (as of mid-March 2021) that have announced 3GPP-compliant 5G for mobile or FWA services. A total of 428 operators in 132 co...
Brief Introduction to SP430 MCU Debug Interface
The MSP430F1, F2, and F4 series products use a 4-wire JTAG interface, namely TMS (mode selection), TCK (JTAG clock signal), TDO (data output), and TDI (...
The following figure shows part of the VGA-OUT circuit:(1) Does D6 function similarly to the output protection function of a motor drive?
(2) If (1) is true, does the VGA interface generate back elect...
After many leaks, Huawei officially announced today that the nova 8 series will be released on December 23. The press conference was held online with the slogan "I am the cameraman". The offi...[Details]
Abstract: This application note presents a reference design for an AR111 lamp LED driver with two parallel strings of five LEDs (5S2P). Using the MAX16819 in buck-boost mode, the circuit operates f...[Details]
TD-SCDMA system is a new type of third-generation mobile communication network system. It provides high-quality voice services, as well as packet data services and other multimedia services at a ra...[Details]
Is the prospect of servo motor controller good? There is a question worth pondering. I wonder if you have noticed that we have entered an era of mechanization. In the past, a large amount of labor wa...[Details]
Due to the recent cold wave and snowstorm in the United States, Samsung Electronics' wafer factory in Austin, Texas, was short of electricity and had to be temporarily closed. According to the latest...[Details]
The benchtop multimeter is a commonly used resistance measuring instrument, but in actual applications, do you use the multimeter to measure resistance correctly? Below, Agitek will show you some com...[Details]
Since the high-bit addition of a serial multi-bit adder has to wait for the carry of the low-bit, the speed is limited by the carry signal and becomes slow. People have designed a multi-bit carry-lo...[Details]
First, let's briefly introduce the nRF24L01 wireless module (1) 2.4Ghz global open ISM band license-free use (2) Maximum operating rate of 2Mbps, efficient GFSK modulation, strong anti-interfer...[Details]
The American "Tom Hardware" website reported that AMD, Nvidia, Intel and other companies sell large quantities of advanced chips to China, and the US suppression will inevitably hurt these American c...[Details]
For decades, most motor control applications have relied on common brushed DC and stepper motors that provide low cost and ease of implementation. However, with the continuous innovation and integr...[Details]
Europe has become one of the main destinations for Chinese electric vehicles to go overseas. In 2022, the 16 countries with the highest global market share of electric vehicles (including plug-i...[Details]
According to foreign media reports, Apple officially released the new 2020 MacBook Air/iPad Pro yesterday. The new iPad Pro has added a new LiDAR camera system, which also suggests that the iPh...[Details]
Frequency conversion speed regulation technology is an important development direction of modern electric power transmission technology. As the core of frequency conversion speed regulation system, t...[Details]
As the number of mobile devices using touch panels increases, most of the new generation of mobile devices have abandoned traditional mechanical push switches and switched to full-screen touch or par...[Details]