CA3160E datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> CA3160E

CA3160E: Part NumberCA3160E; CategoryAnalog mixed-signal IC Amplifier circuit; File Size7349.85，17 Pages; ManufacturerHarris; Websitehttp://www.harris.com/

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

CA3160E Overview

Basic information of CA3160E amplifier:

CA3160E is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are DIP, DIP8,.3

CA3160E amplifier core information:

The minimum operating temperature of the CA3160E is -55 °C and the maximum operating temperature is 125 °C. Maximum bias current at 25°C: 0.00005 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of the CA3160E is 10 V/us. The maximum slew rate of the CA3160E given by the manufacturer is 15 mA. Its minimum voltage gain is 50000. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the CA3160E gain becomes 0.707 times the low-frequency gain is 4000 kHz.

The nominal supply voltage of CA3160E is 7.5 V, and its corresponding nominal negative supply voltage is -7.5 V. The power supply range is: 5/15 V. The input offset voltage of the CA3160E is 15000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of CA3160E:

CA3160E has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 2.54 mm.

CA3160E amplifier additional information:

CA3160E adopts the VOLTAGE-FEEDBACK architecture. It belongs to the low-bias class of amplifiers. It does not belong to the low offset class of amplifiers. The frequency compensation status of CA3160E is: YES. Its temperature grade is: MILITARY.

CA3160E is not Rohs certified. The corresponding JESD-30 code is: R-PDIP-T8. The corresponding JESD-609 code is: e0. The packaging code of CA3160E is: DIP. CA3160E packaging materials are mostly PLASTIC/EPOXY.

The package shape is RECTANGULAR. The form of CA3160E package pins is: IN-LINE. Its terminal form is: THROUGH-HOLE.

Recommended Resources

Loop chasing light circuit

Low-pass or high-pass filter circuit using BUF-03

Sensor equivalent circuit diagram

Reverse voltage protection circuit in RTD circuit

Parallel application circuit diagram of two LM396

BIJ9148 (universal) infrared remote control transmitter circuit

【MM32 eMiniBoard Review】+ Serial Communication Control of MP3 Player: The MM32 eMiniBoard development board has two serial ports, namely UART1 and UART2. The serial port can be used for communication and to control serial communication devices, such as MP3 player modules, data recorder modules, serial ultrasonic ran...; jinglixixi Domestic Chip Exchange

I recently found an article (PPT) to solve the EMC problem of a certain system. I just found it after exploring a little bit (share it...: What I shared is a PPT. I sorted out the pictures I tested myself and shared them with you. Of course, they are very accurate pictures. They are very enjoyable to watch. Recommended collection! Electromagnetic interference fault diagnosis ...; btty038 RF/Wirelessly

Will the grounding of the differential line in the figure affect the signal?: The picture shows a double-sided signal adapter board. The customer requested this package. But I feel there will be signal interference. Please give me some advice. How high is the signal frequency? If it is not a very high frequency, it is not a...; asionl PCB Design

【Microchip WBZ451 Curiosity】GPIO Control: This time, GPIO is used to control peripherals, by controlling the button (SW2) and the green light in the RGB lamp respectively. Make a logical judgment based on whether the button is pressed. When the button is pressed, the LED pin is high level; o...; swzswz RF/Wirelessly

The reverse withstand voltage peak of the secondary winding rectifier tube D10 reaches -142V. How can I adjust the RCD parameter value to reduce it?: The target value is reduced to about -110V. Figure 1 shows the secondary winding RCD circuit parameters of the auxiliary power supply. The output is 12V, about 5A, the total output power is about 70W, and the input rated voltage is 390V. The maximum...; 西里古1992 Analog electronics

Why when I search for the definition of the flash_open() function, I find #define flash_open(): There is a function flash_open() in a function. When looking for the definition of this function, it is found that #define flash_open(). If this flash_open() function is a system native function, then why is #define flash_open() still needed? ...; 一沙一世 MCU

CA3160E Also View