LM10CLWM datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> LM10CLWM

LM10CLWM: Part NumberLM10CLWM; CategoryAnalog mixed-signal IC Amplifier circuit; File Size11817.24，17 Pages; ManufacturerRochester Electronics; Websitehttps://www.rocelec.com/; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
LM10CWM/NOPB	Texas Instruments	Op Amp Dual GP ±20V/40V 14-Pin SOIC W Tube
LM10CWMX/NOPB	Texas Instruments	Op Amp Dual GP ±20V/40V 14-Pin SOIC W T/R
LM10CWM	Texas Instruments	Operational Amplifier and Voltage Reference 14-SOIC 0 to 70
LM10CWMX	National Semiconductor Corporation	Basic information of LM10CWMX amplifier:LM10CWMX is an OPERATIONAL AMPLIFIER. Commonly used packagin...
LM10CLWMX	Texas Instruments	Basic information of LM10CLWMX amplifier:LM10CLWMX is an OPERATIONAL AMPLIFIER. The commonly used pa...

LM10CLWM Overview

Basic information of LM10CLWM amplifier:

LM10CLWM is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are 0.300 INCH, PLASTIC, SOP-14

LM10CLWM amplifier core information:

The minimum operating temperature of the LM10CLWM is and the maximum operating temperature is 70 °C. Its peak reflow temperature is NOT SPECIFIED Its maximum average bias current is 0.03 µA

The upper limit of its supply voltage is 7. The input offset voltage of VLM10CLWM is 4000 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of LM10CLWM:

The width of LM10CLWM is: 7.5 mm and the length is 9 mm. LM10CLWM has 14 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 14

LM10CLWM amplifier additional information:

Its temperature grade is: COMMERCIAL. And its humidity sensitivity level is: NOT SPECIFIED. The LM10CLWM is not Rohs certified. It does not contain lead. The corresponding JESD-30 code is: R-PDSO-G14.

The corresponding JESD-609 code is: e0. The packaging code of LM10CLWM is: SOP. The materials used in the LM10CLWM package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The LM10CLWM package pin forms are: SMALL OUTLINE.

Its terminal forms are: GULL WING. The maximum seat height is 2.65 mm.

Recommended Resources

Differential bridge amplifier circuit diagram

Rural fish farming control circuit

PTC three-phase asynchronous motor protection circuit 8

Position signal transmitter circuit

555 AC power recovery automatic sound and light annunciator circuit (1)

1.5v LED flash circuit

The pressure sensor outputs the pressure value in a table: @littleshrimp The pressure sensor's pressure value, temperature value, and humidity value are output in a table, and are sampled every 30 minutes. How to get started? Using SensorTile.box? Use "SensorTile.box". Display air pressure, ...; lanhua ST MEMS Sensor Creative Design Competition

MCU interrupt: Please help me write the program in assembly language After C51 is compiled, assembly code can be automatically generated The problem is that there is no computer around. Looks like an exam. Remember to compile the C program in keilc and enter ...; 李吉利 51mcu

SD card FAT16 reading and writing program based on MSP430 learning and development system: SD card FAT16 reading and writing program based on MSP430 learning and development system The basic structure and technical characteristics of SD card are introduced, the FAT16 file system designed by using MSP430 microcontroller and SD card is de...; Aguilera Microcontroller MCU

Help! After connecting the signal generator with a BNC to SMA cable, the multimeter at the SMA end is very small: The input is 3V, but the other end is not connected to the circuit. The voltage measured by the multimeter is only a few tenths of a volt. However, the output terminal of the signal generator is a normal 3V. Is there something wrong with the wirin...; wuzhihui1999 Analog electronics

How to detect if there is water in the pipe?: To detect whether there is water in the pipe, a water level sensor is needed. Generally, a pipe water level sensor is more suitable for detecting liquid in the pipe. The pipe water level sensor uses optical principles to detect. There are two type...; 能点科技1 Sensor

FPGA-based neural network hardware implementation method.pdf: FPGA-based neural network hardware implementation method.pdf The course is at the undergraduate level, not even CNN, and there is no source code. It is too elementary. How to make full use of the field programmable features of FPGA to realize th...; zxopenljx EE_FPGA Learning Park

LM10CLWM Also View