10445 views|29 replies

3180

Posts

0

Resources
The OP
 

Please design a pressure sensor conversion circuit [Copy link]

 
The pressure sensor parameters are as follows: Requirements: Output 0~3.3V. Thank you!

This post is from Analog electronics

Latest reply

The problem is: you use a Dan power supply, and the output range of INA188 can only be 0.25V lower than the positive end of the power supply to 0.25V higher than the negative end of the power supply. Therefore, when the potential of your two input terminals (sensor output terminals) is equal, the output of the op amp cannot reach zero, but 0.25V higher than zero (negative end of the power supply). [attach]399286[/attach] It is best to use dual power supplies and ground the REF terminal.   Details Published on 2019-1-17 17:27
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。

2w

Posts

0

Resources
2
 
This sensor seems to be a bridge circuit. If so, then use an instrumentation amplifier to amplify the sensor signal. Note that the power supply to the sensor must be stable enough.
This post is from Analog electronics
 
 

1w

Posts

142

Resources
3
 
The manual should contain a wiring diagram or wiring instructions. The gain can be determined based on the sensor output range and the required signal amplitude, and can be achieved using an op amp.
This post is from Analog electronics
 
Personal signature上传了一些书籍资料,也许有你想要的:http://download.eeworld.com.cn/user/chunyang
 
 
 

6366

Posts

4936

Resources
4
 
Generally, regular manufacturers will provide typical circuits in the user manual, just follow them.
This post is from Analog electronics

Comments

Just two pieces of paper  Details Published on 2019-1-14 09:30
 
 
 
 

3180

Posts

0

Resources
5
 
tiankai001 posted on 2019-1-14 09:19 Generally, regular manufacturers will provide typical circuits in the user manual, just follow them
Just two pieces of paper
This post is from Analog electronics

Comments

Just two sheets of paper must have wiring instructions (which two wires are power, which two wires are signal, and indicate the polarity), power supply voltage range, sensor sensitivity...  Details Published on 2019-1-14 11:46
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

28

Posts

0

Resources
6
 
This is a force sensor for a mechanical testing machine. It has an internal bridge circuit and is driven by DC voltage. It can measure tension and pressure.
This post is from Analog electronics
 
 
 
 

666

Posts

5

Resources
7
 
It looks like a resistive type. Just design a transmitter using an ultra-low power microcontroller.
This post is from Analog electronics
 
 
 
 

2w

Posts

0

Resources
8
 
chenbingjy posted on 2019-1-14 09:30 Just two pieces of paper
Just two pieces of paper, there must be wiring instructions (which two wires are power, which two wires are signal, and indicate the polarity), power supply voltage range, sensor sensitivity...
This post is from Analog electronics

Comments

I have posted those two pieces of paper.  Details Published on 2019-1-14 11:47
 
 
 
 

3180

Posts

0

Resources
9
 
maychang posted on 2019-1-14 11:46 There must be wiring instructions (which two wires are power and which two wires are signal, and indicate the polarity), power supply voltage range, sensor sensitivity...
I have posted those two pieces of paper
This post is from Analog electronics

Comments

"I have posted those two pieces of paper." Yes, they are posted. What happens after posting them? Chunyang on the 3rd floor has already said: use op amps to achieve it. I said on the 2nd floor: use instrument amplifiers to amplify the sensor signal. I also added another sentence: pay attention to the power supply to the sensor to be sufficient  Details Published on 2019-1-14 12:25
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

2w

Posts

0

Resources
10
 
chenbingjy posted on 2019-1-14 11:47 I have posted those two pieces of paper
"I have posted those two pieces of paper" Yes, they are posted. So what? Chunyang on the 3rd floor has already said: Use op amps to achieve it. I said on the 2nd floor: Use instrumentation amplifiers to amplify the sensor signal. I also added one more sentence: Make sure the power supply to the sensor is stable enough.
This post is from Analog electronics

Comments

But now there is a problem, I don't know how to check  Details Published on 2019-1-14 13:02
 
 
 
 

3180

Posts

0

Resources
11
 
maychang posted on 2019-1-14 12:25 "I have posted those two pieces of paper" Yes, they are posted. What happens after posting them? Chunyang on the 3rd floor has already said: use op amps...
But now there is a problem, I don't know how to check
This post is from Analog electronics

Comments

“But now there is a problem.” “There is a problem” means your circuit has a problem. Where is your circuit?  Details Published on 2019-1-14 15:30
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

2w

Posts

0

Resources
12
 
chenbingjy posted on 2019-1-14 13:02 But now there is a problem, I don’t know how to check it
“But now there is a problem” “There is a problem”, and it is also your circuit that has a problem. Where is your circuit?
This post is from Analog electronics

Comments

I posted my circuit. [attachimg]398634[/attachimg]  Details Published on 2019-1-14 15:36
 
 
 
 

3180

Posts

0

Resources
13
 
maychang posted on 2019-1-14 15:30 "But now there is a problem" "There is a problem", and it is also your circuit that has a problem. Where is your circuit?
I posted my circuit.


This post is from Analog electronics

Comments

"I posted my circuit." The circuit you posted does not include the sensor or the power supply for the sensor.  Details Published on 2019-1-14 15:48
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

2w

Posts

0

Resources
14
 
"I posted my circuit." The circuit you posted does not include the sensor or the power supply of the sensor.
This post is from Analog electronics

Comments

Thank you maychang. [attachimg]398642[/attachimg]  Details Published on 2019-1-14 15:54
 
 
 
 

3180

Posts

0

Resources
15
 
maychang posted on 2019-1-14 15:48 "I posted my circuit." The circuit you posted does not include the sensor or the power supply of the sensor.
Thank you, maychang.


This post is from Analog electronics

Comments

In your first post, the "two pieces of paper" had the definitions of red, black, green, and white lines marked below, but your 15th post did not have any color markings.  Details Published on 2019-1-14 16:15
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

2w

Posts

0

Resources
16
 
In your first post, the "two pieces of paper" have the definitions of red, black, green and white lines marked below, but you have no color markings in the 15th post.
This post is from Analog electronics

Comments

I did have the first piece of paper, and my boss showed it to me. I didn’t have the second piece of paper, but my boss asked a worker in the factory to take a picture of it today in order to post it.  Details Published on 2019-1-14 16:25
 
 
 
 

3180

Posts

0

Resources
17
 
maychang posted on 2019-1-14 16:15 In the first post, your "two pieces of paper" have the red, black, green and white lines marked below, but your 15th floor has no color markings.
It turns out that the first piece of paper does exist, and the boss showed it to me. I don't have the second piece of paper, but the boss asked the factory workers to take a picture of it today in order to post a message.
This post is from Analog electronics

Comments

"It turns out that I do have the first piece of paper. My boss showed it to me. But I don't have the second piece of paper." Then no one can do anything.  Details Published on 2019-1-14 17:21
"It turns out that I do have the first piece of paper. My boss showed it to me. But I don't have the second piece of paper." Then no one can do anything.  Details Published on 2019-1-14 17:19
"It turns out that I do have the first piece of paper. My boss showed it to me. But I don't have the second piece of paper." Then no one can do anything.  Details Published on 2019-1-14 16:54
"It turns out that I do have the first piece of paper. My boss showed it to me. But I don't have the second piece of paper." Then no one can do anything.  Details Published on 2019-1-14 16:33
"It turns out that I do have the first piece of paper. My boss showed it to me. But I don't have the second piece of paper." Then no one can do anything.  Details Published on 2019-1-14 16:32
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

2w

Posts

0

Resources
18
 
chenbingjy posted on 2019-1-14 16:25 It turns out that the first piece of paper exists, and the boss showed it to me. I don’t have the second piece of paper. Today, in order to post a message, the boss asked the workers in the factory to take a picture.
“It turns out that the first piece of paper exists, and the boss showed it to me. I don’t have the second piece of paper.” Then no one can do anything.
This post is from Analog electronics
 
 
 
 

3180

Posts

0

Resources
19
 
Uncle Maychang, look, I marked it



This post is from Analog electronics
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

3180

Posts

0

Resources
20
 
chenbingjy posted on 2019-1-14 16:25 It turns out that the first piece of paper is there, and the boss showed it to me. I don’t have the second piece of paper. The boss asked the factory workers to take a picture of it today in order to post it.
Then why is there no way? Didn’t I post it?
This post is from Analog electronics
 
Personal signature为江山踏坏了乌骓马,为社稷拉断了宝雕弓。
 
 
 

Guess Your Favourite
Just looking around
Find a datasheet?

EEWorld Datasheet Technical Support

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号
快速回复 返回顶部 Return list