JFET

CH376S Development Test

Overview

CH376 supports USB device mode and USB host mode, and has built-in basic firmware for USB communication protocol, built-in firmware for processing Mass-Storage mass storage device dedicated communication protocol, built-in SD card communication interface firmware, built-in FAT16 and FAT32 and FAT12 file system management firmware, supports commonly used USB storage devices (including U disk/USB hard disk/USB flash disk/USB card reader) and SD card (including standard capacity SD card and high capacity HC-SD card and protocol compatible MMC card and TF card).

CH376 supports three communication interfaces: 8-bit parallel port, SPI interface or asynchronous serial port. Controllers such as microcontroller/DSP/MCU/MPU can control CH376 chip through any of the above communication interfaces to access files in U disk or SD card or communicate with computer.

Design Files

Related Devices

Devices	Class	introduce	Datasheet
5S0-1200A2020-00	Analog mixed-signal IC;Into the crystal resonator (passive)		Download
R1206RXX102XJ04LTC	Passive components;SMD resistor	Resistance (ohms): 1K Accuracy: ±5% Power: 1/4W	Download
CH376S	Analog mixed-signal IC;The USB chip	Number of Drivers/Receivers: - Protocol Category: USB 2.0 Type: Transceiver Data Rate: 12Mbps File Management Chip	Download
U-A-24DD-Y-1	The connector;The USB connector	Male and Female: Female Connector Type: USB - Type A Number of Contacts: 4 Standard: USB 2 USB Female	Download
nSMD010	Circuit protection;PTC self recovery fuse	Maximum voltage: 60V Trip current: 250mA 0.10A, 60V, self-restoring fuse	Download
2.54mm,2×10双排排母直	The connector;Mother row needle row	Number of pins: 20 Connector type: Number of busbars: 2 Contact type: Female socket spacing: 0.100" (2.54mm) Plastic height 8.45mm	Download
C1206X7R102K202NR0	Passive components;The patch capacitance	Accuracy: ±10% Capacitance: 1nF Rated voltage: 2kV Temperature drift coefficient (dielectric material): X7R X7R	Download

All reference designs on this site are sourced from major semiconductor manufacturers or collected online for learning and research. The copyright belongs to the semiconductor manufacturer or the original author. If you believe that the reference design of this site infringes upon your relevant rights and interests, please send us a rights notice. As a neutral platform service provider, we will take measures to delete the relevant content in accordance with relevant laws after receiving the relevant notice from the rights holder. Please send relevant notifications to email: bbs_service@eeworld.com.cn.

It is your responsibility to test the circuit yourself and determine its suitability for you. EEWorld will not be liable for direct, indirect, special, incidental, consequential or punitive damages arising from any cause or anything connected to any reference design used.

Hot

Technical Resources More

Search Datasheet?

Supported by EEWorld Datasheet

Technical Videos More

Forum More

Update:2024-11-15 01:36:56

Design of Multi-machine Communication Dispatch and Command System with I2C Bus
The structure, working principle and data transmission mode of I2C bus are discussed. The design of multi-machine communication software and hardware based on I2C bus is discussed, and a program-contr
Tetris_Verilog Course Design.rar
Tetris_Verilog Course Design.rar
Will directly connecting the solder joint to the copper pad cause the heat to transfer too quickly and make soldering difficult?
I have a question. I am drawing a board, and the GND pins of several capacitors are very close to the GND copper. I just put the GND pins of the capacitors directly on the copper. Then the software sh
Several questions about MmwaveStudio
Question 1: What are the parameters for the Sensor configuration option in MmwaveStudio and what are its meanings? There is some confusion when configuring the mmwavestudio sensor configuration option
How to Improve Electronic Product Heat Dissipation through Good PCB Design
[align=left][color=rgb(51, 51, 51)]For electronic equipment, a certain amount of heat will be generated when working, which will cause the internal temperature of the equipment to rise rapidly. If the
The output waveform of the Wien oscillator circuit is abnormal
The output waveform is shown in the figure above, the circuit schematic is as shown below, the op amp power supply is positive and negative 8V No matter how you adjust the sliding rheostat, the output

Datasheet More

Circuits More