sigma

【2023 Electronic Competition】Power supply electronic competition questions

Overview

The system block diagram of the BUCK-BOOST main power board
digital synchronous rectification BUCK-BOOST converter is shown in Figure 1.
1. All output currents are not less than 500mA;
2. Input voltage: 12-48V;
3. Output voltage: 0-48V ;
4. Output current: rated current 2A, maximum current: 4A;
5. Two buttons control the step increase or decrease of the output voltage respectively (step voltage 0.1V);
6. Power supply efficiency is not less than 85%;
7. With circuit protection Function (overvoltage protection; overcurrent protection) and operation, fault and other status indications;
8. The output current and current are displayed by the OLED screen to 2 decimal places;
9. Power supply ripple: All measured voltage ripples are required Less than 50mV, 2 points will be deducted for every 10mV increase;
10. The output voltage value can be saved, and the output voltage value can be adjusted to the value specified by the judges. When the power is turned off and on again, the voltage value remains unchanged.

Design Files

Picture 1.png

Related Devices

Devices	Class	introduce	Datasheet
CL21A106KBYQNNE			Download
SMDRI127-220MT	Passive components;Power inductor	Accuracy: ±20% Rated current: 3.6A DC resistance (internal resistance): 43mΩ Inductance value: 22uH	Download
PA2512FKE7W0R001E	Passive components;Patch low resistance of sampling resistor	Power: 2W Accuracy: ±1% Resistance (ohms): 0.001 Temperature coefficient: ±50 ppm/℃	Download
EG2104	Other integrated circuit (IC);MOS driver	Cost-effective, 600V, half-bridge Nmos pre-driver	Download
INA282AIDR	Analog mixed-signal IC;Amplifier circuit	Common mode input voltage: -14V ~ 80V Gain (amplification factor): 50 V/V Number of channels: 1 Op amp type: Current Sense Monitoring type: High Side Operating bandwidth: 10kHz Operating voltage: 2.7V ~ 18V	Download
TLMG1100-GS08	LED optoelectronic/LED;photoelectric	Illumination Color: Yellow Green Main Wavelength/Color Coordinate: 570nm Color Temperature - CCT (K): -	Download
GS8552-SR	Analog mixed-signal IC;Precision op-amp	Gain bandwidth product (GBP): 1.8MHz Number of amplifier groups: 2 Op amp type: Zero-Drift Power consumption of each channel: 180uA Slew rate (SR): 0.95 V/us Supply voltage: 1.8V ~ 5.5V 1.5MHZ, rail To orbit, high precision 1uV (5uV, Max, 25°C), low temperature drift 0.05uV/℃ (Max.)	Download
RVT1H471M1213	Passive components;Patch type aluminum electrolytic capacitors	Capacitance: 470uF Accuracy: ±20% Rated voltage: 50V	Download
IRF540N			Download
XL7005A	Power/power management;DC - DC chip	Output current: 400mA Switching operating frequency: 150kHz Output type: Adjustable Number of output voltage channels: 1 Function type: Step-Down Output configuration: Positive	Download
CGA4J1X7S1C106KT000N	Passive components;The patch capacitance	Accuracy: ±10% Capacitance: 10uF Rated voltage: 16V Temperature drift coefficient (dielectric material): X7S	Download
CDRH74-101MT	Passive components;Power inductor	Accuracy: ±10% Inductance value: 100uH DC resistance (internal resistance): 610mΩ Rated current: 600mA 100uH patch shielded inductor	Download
AMS1117-3.3	Power/power management;Low dropout linear regulator (they)	Output type: Fixed Maximum input voltage: 18V Output current: 1A Output voltage (minimum/fixed): 3.235V	Download
AMS1117-5.0	Power/power management;Low dropout linear regulator (they)	Output type: fixed Maximum input voltage: 15V Output current: 1A Output voltage (minimum value/fixed value): 5V. Fixed output voltage 5V	Download

All reference designs on this site are sourced from major semiconductor manufacturers or collected online for learning and research. The copyright belongs to the semiconductor manufacturer or the original author. If you believe that the reference design of this site infringes upon your relevant rights and interests, please send us a rights notice. As a neutral platform service provider, we will take measures to delete the relevant content in accordance with relevant laws after receiving the relevant notice from the rights holder. Please send relevant notifications to email: bbs_service@eeworld.com.cn.

It is your responsibility to test the circuit yourself and determine its suitability for you. EEWorld will not be liable for direct, indirect, special, incidental, consequential or punitive damages arising from any cause or anything connected to any reference design used.