红水杯

DLT100AGEVB: Dynamic Load Tool 100 A Evaluation Board

Overview

The Dynamic Load Tool or Active Load Tool is designed for testing power supplies and other forms/sources of electricity. It provides an accurate output reference to confirm that the output voltage and current are within the required range for a predetermined range of loads and conditions, from no load to maximum load. 100A 输出载值包括： 100A 多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点

多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点多点
多点多点多点多点多点多点多点多点多点多点

多点dependent) Output load voltages from 0.5V to 12V High and Low load drives for current sensing accuracy: High load = 5mV/Amp, Low load = 25mV/Amp Slew rate controllable for applications from 1A to 100A

Design Files

All reference designs on this site are sourced from major semiconductor manufacturers or collected online for learning and research. The copyright belongs to the semiconductor manufacturer or the original author. If you believe that the reference design of this site infringes upon your relevant rights and interests, please send us a rights notice. As a neutral platform service provider, we will take measures to delete the relevant content in accordance with relevant laws after receiving the relevant notice from the rights holder. Please send relevant notifications to email: bbs_service@eeworld.com.cn.

It is your responsibility to test the circuit yourself and determine its suitability for you. EEWorld will not be liable for direct, indirect, special, incidental, consequential or punitive damages arising from any cause or anything connected to any reference design used.

Hot

Technical Resources More

Search Datasheet?

Supported by EEWorld Datasheet

Technical Videos More

Forum More

Update:2024-11-15 02:26:15

Playing with Zynq Serial 3 - Introduction to AXI Bus Protocol 1
1 Introduction to AXI ProtocolThe AMBA AXI ( Advanced eXtensible Interface ) protocol is a bus protocol designed for high-performance, high-bandwidth systems and can meet the bus interconnection requi
PHYTEC's imx8mplus development board review
We received the imx8mplus development board from PHYTEC for evaluation, and last time we had it up, everything was working fine. The official website comes with a paper document for rapid development,
[RVB2601 Creative Application Development] 4. Use RTC to record time
[i=s]This post was last edited by hehung on 2022-3-6 19:28[/i]PrefaceRTC is a good choice for recording time. It does not require an external clock chip and can also achieve the purpose of obtaining a
ADN8834 does not work or has current overshoot
1. ADN8834 power-on probability VREF oscillation causes the chip to not work Oscillation phenomenon; Test conditions: VLIM=0V~0.5V, T=25C, VCC RC: 30ohm, 22nf; ICC=10mA when VERF is normal, abnormal c
A brief discussion on the bus differences of ARM Cortex-m0/m4 series
Let’s start with a simple question: How fast can the GPIO flip speed of STM32 (for example, used to simulate timing) be? Write a piece of code to test: [code]void test(void) { for(;;) { GPIOA->ODR = (
Please help me interpret this article about tl431 bias current
https://www.baidu.com/sf_edu_wenku/view/326acdef172ded630b1cb6b7 I don't know where the original post came from. . The first question. . Are α and β equal in the third equation? Otherwise, how did the

Datasheet More

Circuits More