Concurrently manage 8 tubes for the whole bridge

WeChat picture_20220419141718.jpg

WeChat picture_20220419141719.jpg

WeChat picture_202204191417181.jpg

WeChat picture_202204191417182.jpg

WeChat picture_20220419142654.jpg

BOM download

PCB_PCB_Parallel management of full bridge 8 tubes_2022-09-22.pdf

PCB_PCB_Parallel management of full bridge 8 tubes_2022-09-22.json

PCB_Parallel management of full bridge 8 tubes_2022-09-22.pcbdoc

Gerber_PCB_Parallel management of full bridge 8 tubes.zip

Schematic_Parallel management of full bridge 8 tubes_2022-09-22.pdf

SCH_Parallel management of 8 tubes in the full bridge_2022-09-22.json

Sheet_1_2022-09-22.schdoc

62020

【Collection】Happy little duck

Introduction: Based on Yuxin's YX-2.4G single-chip transceiver and bidirectional IO monitoring and frequency communication, it cooperates with 1818AM to realize 4-channel motor forward and reverse drive

The 4-channel remote control produced this time is simple to make, has the right level of difficulty, has a high success rate, and does not even require debugging. It can be completed very quickly and efficiently in some basic productions! Make your own model move! It is also
very happy to be able to personally experience the charm of wireless remote control and enrich your life during the summer vacation ! (๑>؂<๑) Delicious!
Thank you Jialichuang EDA@Jialichuang!
Convenient and efficient board-making service support! Provide us with excellent circuit boards!
All merchants or stores that appear are not advertised! No advertising! No advertising! No advertising!
The first-person and third-person test videos of Duck@Car are in the attachment!
This time, a domestically produced 2.4G+MCU packaged chip is used. It is an integrated chip produced by Yuxin Microelectronics. It codes an 8-function remote control car IC and controls the forward and reverse rotation of 4 sets of motors at the same time.
Also used with 1818AM, each one has two H-bridges integrated inside, which can directly drive two DC motors. The average output current of 1.8 A is enough to satisfy this application scenario.
The main features are
low power consumption, convenient design, and saving hardware costs. The bottom layer of the chip has its own communication protocol, and the onboard micro-antenna can be used. As long as simple peripheral circuits are used, it can work normally.
This modification is very convenient.
A charge and discharge management TP4056 is added to the launch board, which saves you the trouble of finding a battery.
A small 200 mAh battery, thanks to its low power consumption, can also be played for an entire afternoon, but it still has a launch distance of 50 meters.
Note that
on the launch board, I merged the two channels into one group for forward and reverse, which can spread some power and reduce the heat of 1818AM. When
receiving
the second version of the board, the soldering pads were replaced with spring-type terminals, which made wiring more convenient and operation smoother!
The standard length of the antenna is 34mm!
The design logic
draws power from USB → boosts the charge to the battery through XL6019. Because it is a non-standard charging voltage, no special charging and discharging power management chip is used.
The recommended maximum charging voltage is 7.5V, and the maximum withstand voltage of 1818AM is 8V.
Welding recommendations for
C4 and C6 chip capacitors are best to put some solder paste on the pads, align them, and use a soldering iron to solder them.
Battery→Power distribution LDO chips
are AMS1117 and 78M05 respectively, which respectively supply the receiving power supply and the +3.3v required by 1818AM, and a set of 5V output power supply, which simultaneously supply power to the relay and also serve as an output to power the TF card player.
The water is clear and the bottom is crystal clear.
The positive VCC output power of the battery is set to 1818AM. Since the motor works underwater, it has greater power and can be provided with an appropriate heat sink. When the power voltage is ≥6v, a heat sink should also be provided.
In the binding method,
first turn on the power supply of the receiving board and then the transmitting board. When the frequency binding is successful, the receiving board indicator light is always off and the transmitting board indicator light is always on. There is a teaching video attached!
Notes on modification:
In order to save costs, a miniature water pump was used to modify the submersible motor with moderate power. Buy a horizontal type with 2 pairs of front and back blades.
Modify the motor and install it like this. It is recommended to use AB or hot melt glue when bonding, and 704 silicone rubber for waterproofing.
The three channels are used to control the entire duck, forward, backward, (turn left, turn right, use one channel)
, and the two-layer grip is more comfortable.
This channel of SW is used here to control the pause and start of the player.
For example, you can use it to light firecrackers wirelessly during the New Year, haha~
There is a first-person perspective video in the attachment.
At this point, our little duck has been modified. Let’s quickly call our friends to modify one! Come on
remote control car
! (๑>؂<๑) Yummy!

39b42e03763ab07e0708699e8f6d41a2.mp4

bacafb7771a0fa8d385c2c2e467b1fb5.mp4

WeChat picture_20220719120953.jpg

WeChat picture_20220719121012.jpg

WeChat picture_20220730224511.jpg

WeChat picture_20220730224852.jpg

WeChat picture_20220730224859.jpg

WeChat picture_202207301618151.jpg

WeChat picture_202207301618152.jpg

WeChat picture_202207301618155.jpg

321e19e3c68e8e0240461e0b43bc0a3f.mp4

22d03b75d936e0165d35d062a083ed0f.mp4

beacd4e9034fb4ceb3022b015503224f.mp4

57d86ef672f4010245ba9af60045a2a7.mp4

WeChat picture_20220731221007.jpg

WeChat picture_202207312210071.jpg

WeChat picture_202207312210072.jpg

b4bb87e3552e246dd27dfd14c54dbaff.mp4

7eb89eaaadf87527ab439f4488a7800e.mp4

d569fcddb3ae038d7fa1fed46ac1aed3.mp4

BOM download

PCB_Receiver Board [Solicitation Order] Happy Little Duck_2_2022-09-22.pdf

PCB_Receiver Board [Solicitation Order] Happy Little Duck_2_2022-09-22.json

Receiving Board【Solicitation Order】Happy Little Duck_2_2022-09-22.pcbdoc

Gerber_Receiving Board【Solicitation Order】Happy Little Duck_2.zip

PCB_Remote Control [Solicitation Order] Happy Little Duck_2022-09-22.pdf

PCB_Remote Control [Solicitation Order] Happy Little Duck_2022-09-22.json

Schematic_[Solicitation Order] Happy Little Duck_2022-09-22.pdf

SCH_[Solicitation Order] Happy Little Duck_2022-09-22.json

[Solicitation Order] Happy Little Duck_2022-09-22.zip

Remote Control [Solicitation Order] Happy Little Duck_2022-09-27.pcbdoc

Gerber_Remote Control [Solicitation Order] Happy Little Duck.zip

62021

electronic