sigma

Daughter board/adapter board for SPC564 series devices in BGA324 package

SPC564AADPT324S

Overview

The SPC564AADPT324S, SPC563MADPT144S and SPC563M64A176S are evaluation systems supporting the STMicroelectronics SPC56xx family of automotive microprocessors.

The complete system consists of an SPC56XXMB motherboard and a mini module which plugs directly into the motherboard. Different mini modules are available for evaluating the whole family of devices in all supported packages.
The evaluation system (motherboard and daughter card) allows full access to the CPU, all the CPU's I/O signals, and the motherboard peripherals (such as CAN, SCI and LIN). The mini modules itself can be used as a standalone unit when access to the I/O pins or peripherals is not needed.
The MCU is not included, it must be purchased separately. Please contact your sales representative for more details.

Main features

SPC560xx modular evaluation system
On/off power switch with LED indicators
Board power supply: 12 VDC external supply voltage
Onboard STMicroelectronics L9758 voltage regulator with three simultaneous output at 1.2 V, 3.3 V and 5 V
Possibility to configure onboard peripherals to operate at 5 V or 3.3 V logic levels, depending on target
Two CAN channels with jumper enable
- One CAN channel with High-Speed transceiver and DB9 male connector
- One CAN channel with Low-Speed Fault Tolerant and High-Speed transceiver (selectable with jumpers) and DB9 male connector
Up to two LIN channels with jumper enable
- One channel with transceiver and pin header connector populated
- One channel with footprints only
One SCI channel with jumper enables, transceiver and DB9 female connector
Two FlexRay channels with jumper enables
- One channel with transceiver and DB9 male connector
- One channel with footprint only

Four user push buttons with jumper enable and polarity selection
Four user LED’s with jumper enables
One potentiometer for analog voltage input
Pin array for accessing all I/O signals
Expansion connectors for accessing all I/O signals
Prototyping area with 0.1” spacing and SOIC footprint
Specifications:
- Board size 110 mm x 75 mm (SPC563Mxx)
- Board size 120 mm x 95 mm (SPC564Axx)
- 12 VDC Center Positive power supply with 2.5/5.5 mm barrel connectory
Standard connectors to SPC56XXMB

Design Files

SPC563Mxx, SPC564Axx microcontroller family evaluation board

All reference designs on this site are sourced from major semiconductor manufacturers or collected online for learning and research. The copyright belongs to the semiconductor manufacturer or the original author. If you believe that the reference design of this site infringes upon your relevant rights and interests, please send us a rights notice. As a neutral platform service provider, we will take measures to delete the relevant content in accordance with relevant laws after receiving the relevant notice from the rights holder. Please send relevant notifications to email: bbs_service@eeworld.com.cn.

It is your responsibility to test the circuit yourself and determine its suitability for you. EEWorld will not be liable for direct, indirect, special, incidental, consequential or punitive damages arising from any cause or anything connected to any reference design used.

Hot

Technical Resources More

Search Datasheet?

Supported by EEWorld Datasheet

Technical Videos More

Forum More

Update:2024-11-15 08:02:49

Controlled by "Playpad" + Siri + shortcut commands + XCC3200 (MQTT)
Some time ago, a "shortcut command" was added to the mobile phone system update. I also saw others using shortcut commands to control the ESP8266 output. This is indeed more suitable for us electronic
msp430f5529 dual output pwm wave
#include msp430.hextern unsigned int period,period1;int pwm1(period,period1) adjust duty cycle{P2DIR |= BIT0+BIT5;// P2.0 and P2.1 outputP2SEL |= BIT0+BIT5;// P2.0 and P2.1 options selectTA1CCR0 = 100
Why should a DC-DC converter be used as close to the point-of-load (POL) power supply as possible?
Efficiency and accuracy are two major advantages, but implementing POL conversion requires careful attention to regulator design.Proximity to the source. This is one of the best ways to improve the vo
Some subway stations in London have codes on their steps!
[size=5][color=#000000][backcolor=lightblue]The designer of the London Underground steps may be a programmer... [/backcolor][/color][/size][backcolor=lightblue][font=Arial, "][size=5][color=#000000]So
Are you choosing the right power switch solution? Discrete MOSFET vs Integrated Load Switch
A power switch generally refers to connecting and disconnecting power to a load. A power switch sits between the system power supply and the load, and this switch controls when power is or is not supp
[Sipeed LicheeRV 86 Panel Review] Review 1: Unboxing and demo experience
Sipeed LicheeRV 86 development board, why is it called 86:86 panel usually refers to the panel of household switches, sockets, information sockets, etc. Because the length and width are both 86 mm, th

Datasheet More

Circuits More