Training

Location:Training / Circuit Fundamentals / Analog / Fundamentals of Analog Electronics Technology / Discussion 2 of Power Amplifier Circuit (Circuit Identification and Fault Analysis)

You can log in to your eeworld account to continue watching：
Discussion 2 of Power Amplifier Circuit (Circuit Identification and Fault Analysis)
Login

Duration：10 minutes and 1 seconds
Date：2017/05/21

Uploader：老白菜

Introduction

keywords： Analog electronics Tsinghua University Hua Chengying

The main contents of the course include basic knowledge of semiconductors, basics of amplifier circuits, multi-stage amplifier circuits, integrated operational amplifier circuits, frequency response of amplifier circuits, feedback of amplifier circuits, signal operation and processing, waveform generation and signal conversion, and power amplifier circuits. , DC regulated power supply and image reading of analog electronic circuits, etc. This course enables students to acquire basic knowledge, basic theories and basic skills in analog electronics technology through the analysis and design of commonly used electronic devices, analog circuits and their systems, laying the foundation for in-depth study of electronic technology and its application in professional fields. Base.

Reference textbooks for this course: Hua Chengying, Tong Shibai, "Fundamentals of Analog Electronic Technology", Higher Education Press., 2006

You Might Like

Recommended Posts

Working principle of lithium battery equalization circuit: [i=s] This post was last edited by qwqwqw2088 on 2019-2-11 14:23 Edit[/i] [size=4][color=#000000][backcolor=white] The development of new energy and electric vehicles will use lithium batteries with r; qwqwqw2088 Analogue and Mixed Signal

[SAMR21 new gameplay] 31. Using NVM storage: [i=s]This post was last edited by dcexpert on 2019-10-17 10:55[/i]In SAMR21, part of the flash space can be used to simulate EEPROM, which is called NVM (Non-Volatile Memory). Using EEPROM is simpler; dcexpert MicroPython Open Source section

[ATmega4809 Curiosity Nano Review] Buttons: On the ATmega4809 Curiosity Nano, the button uses PF6, which is also the RST pin and is set to GPIO mode by default. Because there is a 100K pull-up resistor R200 on PF6, there is no need to set the i; dcexpert MCU

Have you fallen into these customer support "pitfalls"? Read the story, write a comment, grab a post and win a gift!: [align=left][b][font=微软雅黑][size=3]No way to get support in the middle of the night, time-consuming to return software to the factory for upgrading, too low efficiency of customer service communication; EEWORLD社区 Test/Measurement

About rail-to-rail op amps: [size=4]1. The so-called rail-to-rail operational amplifier refers to an amplifier whose input and output voltage swings are very close to or almost equal to the power supply voltage. [/size] [size=4]; Jacktang Analogue and Mixed Signal

【TGF4042 signal generator】+ Load capacity test: I have used a function generator from manufacturer A before. Its output protection is quite complete. If the output probe encounters external interference, such as accidentally connecting to a DC powe; 飞鸿浩劫 Test/Measurement

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号