Training

Location:Training / Embedded Development / MCU / Punctual Atomic teaches you step by step how to learn STM32-M3 / USB card reader experiment (M3)

You can log in to your eeworld account to continue watching：
USB card reader experiment (M3)
Login

Duration：1 hours and 11 minutes and 21 seconds
Date：2019/03/21

Uploader：EE大学堂

Introduction

keywords： Microcontroller STM32 Punctual Atom

This video will start from the simplest to the deeper, leading everyone to learn the various functions of STM32F103, and start a new STM32 journey for you.
This video is divided into three parts:
1. Introductory part, which mainly introduces the basic knowledge of STM32;
2. Intermediate part, mainly introduces the use of STM32 basic peripherals, including: GPIO, serial port, timer, external interrupt, etc. After studying this article, you will have a basic introduction to STM32 development.
3. Advanced chapter, mainly introduces STM32 advanced peripherals, including: SDIO, CAN bus, etc.

You Might Like

Recommended Posts

Participating in the HELPER2416 Development Board Student Aid Program: First Impressions and Suggestions: [font=宋体] After waiting for a long time, I finally got the board. Some forum friends have already posted unboxing photos, so I won't. [/font] [font=宋体] I got the board, connected it immediately, and s; shihuntaotie Embedded System

Failed to initialize communication: Now there are three ZigBee nodes. I burned the program of node 1 into the first ZigBee board through the ZigBee emulator, and then burned the program of node 2 into the ZigBee board of node 2. The com; 潇雨如烟6 RF/Wirelessly

msp430 1602 display: [color=Red][color=Red]#include "msp430g2553.h"void delay(int i) {unsigned int a,b; for(a=i;a>0;a--)for(b=1111;b>0;b--);} void busy() {unsigned char BF;P2OUT |=BIT1;P2OUT &=~BIT2;P2OUT &=~BIT0;BF=(P1IN; ww_1 Microcontroller MCU

STM32 trigger interrupt debounce problem: I just started to learn 32 and I am writing a program for drip control. In the last process, I found that the interrupt will be triggered many times in a short period of time. I want to add a debounce; 青竹之初 stm32/stm8

Driving external RF front end via BlueNRG-LP: The BlueNRG-LP is an ultra-low-power Bluetooth low energy SoC device that can reach +8 dBm output power at the antenna connector. However, the maximum output power allowed by the Bluetooth standard is; littleshrimp ST - Low Power RF

National Undergraduate Electronic Design Competition…First Prize Works (3): [i=s]This post was last edited by paulhyde on 2014-9-15 09:06[/i] [size=5]RF signal source, semiconductor thermostat design, multi-channel temperature inspection instrument, human heart rate detection; lk972105 Electronics Design Contest

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号