Training
Profile
A camera, AR-15, Arduino and stepper motor were used, and candy and mechanical components were used to make an AR-15 gun with automatic target detection.
Chapters
Chapter 1：Arduino AR-15 machine gun design-automatic target detection (10 minutes and 38 seconds)
Chapter 2：AR-15 machine gun CAD production and Arduino source code (6 minutes and 0 seconds)
You Might Like
Recommended Posts
- Power supply control principle of three-phase fuel pump used in Mercedes-Benz passenger cars
- Masters, the gasoline pump used in Mercedes-Benz cars currently has three wires UVW coming out of the fuel pump computer to directly control the operation of the three-phase fuel pump. I took it apart
-
asena
Automotive Electronics
- Review summary: Free review of Fudan Micro FM33LG0 series, Winsilver chip
- Activity details: [Free evaluation of Fudan Micro FM33LG0 series, Winsilver chip]Updated to 2021-12-24Evaluation report summary:@xld0932[FM33LG0 Series Development Board Review] 07. LCDSegment Display
-
EEWORLD社区
Special Edition for Assessment Centres
- ESP32-S2-Saola-1 calculates pi
- I usually compare the performance of MCUs by calculating pi, because Python supports large integer operations, and pi calculations happen to use large integers, which can initially reflect the integer
-
dcexpert
MicroPython Open Source section
- DCDC H-bridge circuit, what is the principle of boost and buck?
- I don't use a DCDC drive circuit like this H-bridge. What is the principle of this? Is there any difference between it and the general step-up and step-down?
-
小太阳yy
Switching Power Supply Study Group
- How to measure positive and negative 1.5V signals using a single power supply system?
- How to measure the signal of positive and negative 1.5V using a single power supply system? If the signal changes quickly, it can be measured through coupling. But if it is a signal that changes slowl
-
bigbat
Analog electronics
- [Zhongke Bluexun AB32VG1 RISC-V evaluation board] Current and voltage detection project development
- 1. First create a project, the project name is meterADC2. Then select hardware and enable ADC. Here the board only supports ADC0. The chip supports multiple channels.3. From the file, you can find the
-
北方
Domestic Chip Exchange
Recommended Content
Web users are watching Change
- Power supply control principle of three-phase fuel pump used in Mercedes-Benz passenger cars
- Review summary: Free review of Fudan Micro FM33LG0 series, Winsilver chip
- ESP32-S2-Saola-1 calculates pi
- DCDC H-bridge circuit, what is the principle of boost and buck?
- How to measure positive and negative 1.5V signals using a single power supply system?
- [Zhongke Bluexun AB32VG1 RISC-V evaluation board] Current and voltage detection project development
- Complete list of motor model parameters, no longer worried about not understanding the motor model
- Learn about enhanced eCall car design in one article
- CC2640R2F as master control for DHT11
- HTS221 MakeCode extension (driver)
- [TI star product limited time purchase] + AWR6843ISK OOBdemo quick start
- Calculation of RC parameters for PWM as DAC
- Can sensorless drive completely replace sensory drive?
- Motor drive development communication 3: Software component description
- MP3302DJ chip drives 640*480 LCD screen heating problem
- Is the baud rate for communication between microcontrollers set in advance? Or calculated? Also, why does the crystal oscillator have 11.0592...
- DALSA P3-80-08K40 Line Scan Camera Teardown
- CircuitPython 6.0.0 Alpha 1 released
- I have a problem with the wire pulling. Version 21. Please help me.
- [ESP32-Audio-Kit Audio Development Board Review] 1. Unboxing photos and official information, first power-on
- EEWORLD University ---- Robust Control Theory
- 【GD32307E-START】+ TFT screen driver and icon interface drawing
- 【AT-START-F403A Review】Part 4: IIC driving OLED screen
- Reading notes on "Operational Amplifier Parameter Analysis and LTspice Application Simulation"
- MSP430 MCU key test KEY function
- MPS430F149 MCU_Wireless transmission module based on MSP430 MCU.c
- What kind of accomplishment should an embedded hardware engineer have? I want to change jobs
- #TItraininglearningwithcourtesy#Master this little trick? Make your learning more efficient and easier!
- Please advise, how to calculate the switching frequency of MOS tube?
- The god of bad luck possessed me, and I bombed for two days
Popular Components
Just Take a Look
Hot Downloads
- Analysis of Closed-loop Small Signal Model of Active Clamp Forward Converter
- Design of ROM-based sine wave generator: 1. The sine generator consists of a waveform data storage module (ROM)
- ON Semiconductor ESD Power Protection Improvement Solution.pdf
- Establishment of MTK compilation environment (without simulator)[1].part2.rar
- Can modify PDF documents, very convenient, worthy of everyone\'s attention
- Fast rise time multivibrator
- EZ-USB 2100 series microcontroller principle, programming and application
- TCD2905D_www.ic37.com.pdf
- FPGA design code for prefetchable fifo
- How to design and draw circuit schematic diagram under PROTEUS
MoreHot Articles
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
京公网安备 11010802033920号