Overview
New energy vehicles can be divided into pure electric vehicles (EV) and hybrid electric vehicles (HEV/PHEV) according to their power sources. The vehicle controller is the core control component of new energy vehicles. Its main functions are to analyze driver needs, monitor vehicle driving status, coordinate the work of control units such as BMS, MCU, EMS, TCU, etc., and realize the functions of vehicle power on and off, drive control, energy recovery, accessory control and fault diagnosis.
Features
Based on AUTOSAR software architecture, product functions meet PHEV/EV VCU and HCU development, and the cooperation model is flexible
Provide solutions covering the entire life cycle from functional specification definition, model development, MIL/HIL testing, real vehicle calibration to mass production
With a rich algorithm model library, application software platform development
The VCU platform is iteratively developed, covering passenger cars and commercial vehicles, and supporting more than 30 models
Product functions (functions can be customized according to customer needs)
-
Vehicle mode determination
-
Vehicle drive (torque management)
-
Energy recovery control
-
Cruise control
-
Vehicle anti-slope control
-
Vehicle creep control
-
Vehicle energy distribution
-
High voltage power on and off control
-
High voltage safety monitoring
-
Vehicle thermal management
-
Vehicle fault diagnosis and response
-
Vehicle status monitoring and display
-
Charging monitoring
-
Accessory Control
-
Vehicle anti-theft
-
Mileage calculation
-
Program online upgrade and online calibration
-
Other vehicle customization functions
Product Family Tree
Previous article：Power rear door controller (PLGM)
Next article：How to choose a car inverter
- Popular Resources
- Popular amplifiers
AWT-20236-3RI
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehiclesIntroduction: Connectors are used in every car. The device uses electrical, optical and other signals to control the corresponding mechanical force to connect, disconnect and convert, thereby realizing the corresponding circuit or optical channel conversion. ...
- Wiring harness durability test and contact voltage drop test methodBased on the QC T 29106-2014 standard, this paper proposes a new durability characteristic test and contact voltage drop test method, and conducts experimental verification on these two test methods. ...
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehiclesMetal oxides and their composites with other materials (such as MXenes and metal chalcogenides) can be used to achieve different ...
- Design considerations for automotive battery wiring harnessThe battery is one of the power sources of the car. When the generator stops working and the engine is started, all the power is output from the battery. When the engine is idling or working at a low speed, the power generation of the generator cannot meet the demand. ...
- Do you know all the various motors commonly used in automotive electronics?VALVETRONIC servo motor is a brushless DC motor (BLDC motor), the components of which are shown in Figure 15-7. BLCD motors transfer energy in a non-contact manner, are maintenance-free and have high power. ...
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
- Brief Analysis of Automotive Ethernet Test Content and Test Methods
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehicles
- Wiring harness durability test and contact voltage drop test method
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehicles
- Design considerations for automotive battery wiring harness
- Do you know all the various motors commonly used in automotive electronics?
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
- PCB drawing process shortcut keys
- How to start power supply design
- EEWORLD University ---- Machine Learning
- Has anyone tried the baud rate adaptation of LIN communication?
- Analog Electronics Design
- Will adding a nonlinear link to the RC bridge sine wave oscillation circuit cause waveform distortion?
- Introduction to TI_DSP link command file (*.cmd)
- [N32L43x Review] 2. Turn on the lights, blink, blink, blink...
- EEWORLD University Hall - Talking about the development creativity of electronic products and using network resources to help development
- The output of the op amp in the active integrator circuit oscillates. What should I do?
京公网安备 11010802033920号