1. What is a high frequency inverter?
A power inverter (car power supply) is a convenient power converter that can convert DC12V direct current into AC220V alternating current, the same as the mains power, for use in general electrical appliances.
2. What is the situation in domestic and foreign markets?
Power inverters are widely welcomed in foreign markets. Because of the high penetration rate of cars in foreign countries, when working or traveling in places without mains electricity, you can use an inverter to connect the car battery to drive electrical appliances and power tools.
3. Why promote this product in the country?
After China entered the WTO, more and more people bought cars privately in the domestic market. Therefore, power inverters, as power converters that convert DC to AC when the car is moving, will bring convenience to your life and are also a must-have for car owners.
4. Can the power inverter only be used in vehicle systems?
The power inverter is not only suitable for vehicle-mounted systems, but also can be used in any occasion where there is a DC12V power supply to convert DC12V into AC220V AC power, bringing convenience to your life. 5. How are the high and low voltage alarm and shutdown functions reflected? When the power inverter is in high and low voltage alarm and shutdown, the red LED is on and there is an alarm sound.
6. What is the protection function of the power inverter for the battery?
When the power inverter is in use with the battery, the battery voltage drops to 9.5V and the power inverter will automatically shut down to ensure that the car can start normally and the battery will not be damaged.
7. How does the power inverter realize the battery protection function?
The power inverter automatically implements the battery protection function by means of the internal electronic circuit. 8. What is the most common fault? How to eliminate it? When the power inverter is in use, if there is a shutdown and alarm phenomenon, check the following items:
1) Whether the power of the driven appliance exceeds the rated power value of the inverter.
2) Whether the power inverter is well connected to the battery and the appliance.
3) If it shuts down during use, is it a temperature alarm? In this case, it can be used again after stopping for a period of time.
What should I pay attention to?
When using a power inverter, pay attention to the voltage value of the battery power supply system and read the instructions carefully before use.
Previous article:Guoxin Sichen | BTD21520x for motor drives, insulation voltage up to 5700Vrms
Next article:What is a machine vision computer?
- Popular Resources
- Popular amplifiers
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehicles
- Wiring harness durability test and contact voltage drop test method
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehicles
- Design considerations for automotive battery wiring harness
- Do you know all the various motors commonly used in automotive electronics?
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
- Brief Analysis of Automotive Ethernet Test Content and Test Methods
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- LED chemical incompatibility test to see which chemicals LEDs can be used with
- Application of ARM9 hardware coprocessor on WinCE embedded motherboard
- What are the key points for selecting rotor flowmeter?
- LM317 high power charger circuit
- A brief analysis of Embest's application and development of embedded medical devices
- Single-phase RC protection circuit
- stm32 PVD programmable voltage monitor
- Introduction and measurement of edge trigger and level trigger of 51 single chip microcomputer
- Improved design of Linux system software shell protection technology
- What to do if the ABB robot protection device stops
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehicles
- Wiring harness durability test and contact voltage drop test method
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehicles
- Design considerations for automotive battery wiring harness
- Do you know all the various motors commonly used in automotive electronics?
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
- About Negative Feedback Amplifier Circuit
- GD32E230C development platform is finally built
- Proteus MSP430 MCU simulation example 16 - timer timing 1 second
- Building ESP32-C3 development environment based on window Visual Studio Code: ESP-IDF
- [AT-START-F403A Review] + Unsuccessful W25Q128 Read and Write
- I don't know much about the commonly used domestic device manufacturers.
- Cadence Allegro beginners must read
- [Atria Development Board AT32F421 Review] 1. Unboxing and lighting
- EEWORLD University ---- Introduction to CC2650MODAPluetooth? Low-energy RF module
- Thank you for having me + EE has brought me so much knowledge this year! + Thank you to my family for their support and love! + Thank you to my colleagues and friends for their generous help along the way!