By comparing CCD imaging and FPD imaging methods with various parameters in the table below, it can be seen that CCD imaging has a higher effective utilization rate of X-rays than FPD imaging, and can avoid fatal damage to components caused by long-term X-ray radiation. At the same time, the requirements for temperature, transportation, cost, maintenance, etc. are relatively low, and the signal-to-noise ratio is better than FPD imaging. Therefore, the author believes that CCD imaging is more suitable for X-ray imaging systems such as CR/DR.
Previous article：The breast imaging market is full of smoke. Where can we find the path to technological breakthrough?
Next article：Horizontal comparison: the difference between MRI T1 and T2
- Popular Resources
- Popular amplifiers
LTC1150CJ
Latest Medical Electronics Articles
- High-speed 3D bioprinter is available, using sound waves to accurately build cell structures in secondsA new type of 3D bioprinter. Image source: University of Melbourne, Australia Scientists at the University of Melbourne, Australia have developed a new type of high-speed 3D printer. This advanced bioprinter uses "dynamic boundaries" to ...
- [“Source” Observation Series] Application of Keithley in Particle Beam Detection Based on Perovskite SystemIonizing radiation such as X-rays and gamma rays has been widely studied and applied in various fields such as medical imaging, nondestructive testing, scientific research, etc. Therefore, it is necessary to use highly sensitive and low-cost materials and equipment to detect ...
- STMicroelectronics’ Biosensing Innovation Enables Next-Generation Wearable Personal Healthcare and Fitness DevicesHighly integrated biosensor chip integrates ECG monitoring and neural sensing signal input channels with motion tracking and embedded AI core. New products will be presented at the Munich Electronics Show 2024 held in Munich from November 12 to 15. ...
- China's first national standard for organ chips is officially released, led by the Medical Devices Institute of Southeast UniversityThe first national standard in my country's organ chip field, GB T44831-2024 "General Technical Requirements for Skin Chips", led by Professor Gu Zhongze's team from the Suzhou Institute of Medical Devices of Southeast University, was officially released. ...
- The world's first non-electric touchpad is launched: it can sense contact force, area and position even without electricityOn October 30, the technology media scitechdaily published a blog post yesterday (October 29), reporting that researchers at the University of Tampere have developed the world's first non-electric touchpad. ...
- Artificial intelligence designs thousands of new DNA switches to precisely control gene expression
- Mouser Electronics provides electronic design engineers with advanced medical technology resources and products
- Qualcomm Wireless Care provides mobile terminal devices to empower grassroots medical workers with technology
- Magnetoelectric nanodiscs stimulate deep brain noninvasively
MoreSelected Circuit Diagrams
MorePopular Articles
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
MoreDaily News
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
Guess you like
- [Summary] Review and Outlook, Goodbye 2019, Hello 2020!
- The IO port of the microcontroller can generally be set to three states
- Is the solder in the soldering iron toxic?
- What are the benefits of connecting a PNP transistor and a Zener diode in series to control NMOS?
- Recruiting electronics, communications, and computer engineers
- 【Multi-function Internet Weather Clock】Work Submission
- [Raspberry Pi 4B Review] Review and test of various functions of Raspberry Pi 4
- How to get started with CPLD
- Heart rate detection BLE device based on RSL10
- Introducing the design of bicycle speedometer using Hall sensor using MSP430
京公网安备 11010802033920号