1 Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great significance in terms of saving energy and protecting the environment.
2. Overall structure of controller
3 Charging system software design
The solar photovoltaic panel is connected to the photovoltaic signal processing circuit, and the photovoltaic voltage is sent to the 12 V battery through the PWM charging control circuit. During normal operation, the 12 V battery output voltage is boosted and rectified by the secondary induction of the high-frequency planar transformer to the full-bridge circuit. At the same time, the 12 V output voltage is connected to the voltage conversion circuit to supply power to other circuits of the controller.
2.1 Solar Charging System
The photovoltaic signal processing circuit includes a signal reverse connection protection circuit, a photovoltaic voltage sampling circuit and a lightning protection circuit. Among them, the signal reverse connection protection circuit can prevent the photovoltaic signal reverse connection input from damaging the controller circuit. The voltage sampling circuit provides the sampled photovoltaic voltage signal to C8051F920. The lightning protection circuit can prevent lightning and lightning in the sky from being introduced into the controller and causing damage. The PWM charging control circuit will charge the battery. The PWM signal output by the MCU is used to drive the high-power MOS tube to control the size of the charging voltage to avoid damage to the battery.
2.2 Electronic ballast circuit design
2.3 Design of ignition circuit
Since the metal halide lamp is filled with inert gas, its breakdown voltage is very high, usually required to reach about 20 kV, so the ignition circuit is required to provide a sufficiently high voltage. Based on this, by connecting the secondary of the transformer to the triple voltage ignition circuit shown in Figure 4, a voltage of 1200 V can be obtained, and after connecting it to the metal halide lamp through the lighting coil, a lighting voltage of about 20 kV can be obtained at the two poles of the metal halide lamp.
Previous article：Design and implementation of infrared remote control password lock based on single chip microcomputer AT89C51RC
Next article：Design of multi-channel calling system based on 51 single chip microcomputer
- Popular Resources
- Popular amplifiers
LF157AH/883
Latest Microcontroller Articles
- Download from the Internet--ARM Getting Started NotesA brief introduction: From today on, the ARM notebook of the rookie is open, and it can be regarded as a place to store these notes. Why publish it? Maybe you are interested in it. In fact, the reason for these notes is ...
- Learn ARM development(22)Turning off and on interrupts Interrupts are an efficient dialogue mechanism, but sometimes you don't want to interrupt the program while it is running. For example, when you are printing something, the program suddenly interrupts and another ...
- Learn ARM development(21)First, declare the task pointer, because it will be used later. Task pointer volatile TASK_TCB* volatile g_pCurrentTask = NULL;volatile TASK_TCB* vol ...
- Learn ARM development(20)With the previous Tick interrupt, the basic task switching conditions are ready. However, this "easterly" is also difficult to understand. Only through continuous practice can we understand it. ...
- Learn ARM development(19)After many days of hard work, I finally got the interrupt working. But in order to allow RTOS to use timer interrupts, what kind of interrupts can be implemented in S3C44B0? There are two methods in S3C44B0. ...
- Learn ARM development(14)
- Learn ARM development(15)
- Learn ARM development(16)
- Learn ARM development(17)
He Limin Column
Microcontroller and Embedded Systems Bible
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
MoreSelected Circuit Diagrams
MorePopular Articles
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
MoreDaily News
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
Guess you like
- PICO CO2 Sensor Board
- Pingtouge RVB2601 board-ADC acquisition and CSI
- The LIS2MDL array board welding of the magnetic nail navigation AGV car is completed
- The new evaluation information is here~~
- Use idle STM32 development boards and Freescale development boards
- Can I still install XP on my new desktop computer? I checked some information and it said that BIOS doesn't support it. Is this true?
- Analysis of the working principle of anti-interference filter
- TI: Development platform compatible with multiple wireless communication protocols
- Mountain climbing test of Bluetooth ECG recording module
- My Journey of MCU Development (Part 4)
京公网安备 11010802033920号