In the ADS1.2 environment, when using JLINK to debug NXP's ARM, even if you set up each step according to the instructions, the error message shown in the figure below will still appear.
We can solve this problem through the following settings. Click Options as shown below
After opening the drop-down box, click on the Configure Processor... option, and the following dialog box will appear. Just uncheck the √ in front of the Semihosting mode option, and set the CPU and Flash items correctly in the J-link settings. After setting, close the software and reopen it, and you can perform interrupt simulation in both SRAM and Flash.
Previous article：Linux system installation under SmartArm3250
Next article：SmartARM3250 CF Card User Manual
- Popular Resources
- Popular amplifiers
-
Siemens Motion Control Technology and Engineering Applications (Tongxue, edited by Wu Xiaojun) - Virtualization Technology Practice Guide - High-efficiency and low-cost solutions for small and medium-sized enterprises (Wang Chunhai)
- Learning PLC is easy - PLC ladder diagram and statement table with pictures (Li Changjun, Zhou Hua)
- Operational Amplifier Practical Reference Handbook (Edited by Liu Changsheng, Zhao Mingying, Liu Xu, etc.)
Siemens Motion Control Technology and Engineering Applications (Tongxue, edited by Wu Xiaojun)
Recommended Content
Punctual Atomic teaches you step by step how to learn STM32-M7
Xiaomei Ge’s FPGA introduction to practical special training class full HD record (2019)
Punctual Atomic teaches you step by step how to learn STM32-M4
Punctual Atomic teaches you step by step how to learn STM32-M3
Operating system (RISC-V)
Latest Microcontroller Articles
- Download from the Internet--ARM Getting Started NotesA brief introduction: From today on, the ARM notebook of the rookie is open, and it can be regarded as a place to store these notes. Why publish it? Maybe you are interested in it. In fact, the reason for these notes is ...
- Learn ARM development(22)Turning off and on interrupts Interrupts are an efficient dialogue mechanism, but sometimes you don't want to interrupt the program while it is running. For example, when you are printing something, the program suddenly interrupts and another ...
- Learn ARM development(21)First, declare the task pointer, because it will be used later. Task pointer volatile TASK_TCB* volatile g_pCurrentTask = NULL;volatile TASK_TCB* vol ...
- Learn ARM development(20)With the previous Tick interrupt, the basic task switching conditions are ready. However, this "easterly" is also difficult to understand. Only through continuous practice can we understand it. ...
- Learn ARM development(19)After many days of hard work, I finally got the interrupt working. But in order to allow RTOS to use timer interrupts, what kind of interrupts can be implemented in S3C44B0? There are two methods in S3C44B0. ...
- Learn ARM development(14)
- Learn ARM development(15)
- Learn ARM development(16)
- Learn ARM development(17)
He Limin Column
Microcontroller and Embedded Systems Bible
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
MoreSelected Circuit Diagrams
MorePopular Articles
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
MoreDaily News
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
Guess you like
- 【Want Talent】Beijing-3 embedded positions
- EEWORLD University Hall----Introduction to Digital Power Supply
- SPI interrupt and Main usage issues
- Analysis Example: A Zener Diode Regulator Circuit
- Comparison of CC2540 and nRF51822 application development
- [Evaluation of Anxinke Bluetooth Development Board PB-02-Kit] Light up the LED
- 6. Voltage-divided bias common emitter amplifier circuit
- MSP430F6638 MCU FLL——Frequency Locked Loop
- Bluetooth packaging problem
- 【Qinheng Trial】Five final chapters--IoT system based on CH549
京公网安备 11010802033920号