Eliminate interference with electrical systems and equipment-EEWORLD

Collect

With SCHURTER's EMC expertise and technology, you can find the most suitable EMC solution for your specific application to eliminate interference with electrical systems and equipment.

In addition to being an EMC component manufacturer, SCHURTER also has an EMC engineering support team that provides professional EMC testing to advise you on how to adjust to eliminate interference in your application. Using standard or customized EMC products, we provide you with the most compatible and personalized EMC solutions that pass any test. From the R&D stage to the product cycle of mass production, SCHURTER will be able to provide support throughout the entire process.

Equipped with the test equipment and EMC chambers required to measure conducted emissions, preliminary tests on electrical systems or equipment to determine immunity and emissions are carried out in the SCHURTER EMC Competence Center and Laboratory in Shenzhen. In addition, SCHURTER works closely with accredited laboratories around the world to ensure high standards and compliance.

If required, SCHURTER will provide on-site interference suppression for your electrical equipment using mobile measuring tools. In this way, various conformity tests can be carried out on the system or device to be checked directly at the manufacturer's plant or where the device is in operation.

SCHURTER recommends measuring the leakage current in various operating states for every newly installed machine. The SCHURTER test results will identify excessively high leakage currents and their causes and provide appropriate corrective measures.

All measurement results are documented in an EMC test report, providing proof of CE compliance for conducted emissions.

Reference address：Eliminate interference with electrical systems and equipment

Previous article：High-quality optoelectronic devices for safe circuit isolation
Next article：EMC Countermeasures: TDK expands lineup of notch filters with built-in ESD protection

Recommended ReadingLatest update time:2024-11-16 14:31

Analysis of the Dilemma Faced by the EMC Model of LED Street Lights Contract Energy Management

According to the characteristics of the "Contract Energy Management" model, this paper comprehensively analyzes the confusion of LED street lamps in the process of implementing the "Contract Energy Management" model, and proposes that giving full play to the leading role of the government is the fundamental way out for

[Power Management]

Detailed explanation of MCU EMC test

Here we explain the definition of EMC, the test methods of EMC in single chip microcomputer application systems, the application of new EMC devices and new materials, and troubleshooting techniques. As long as you are engaged in the research and development, production or supply of electronic products, you must conduc

[Microcontroller]

EU unified mobile phone USB interface and its EMC test requirements

Starting from January 1, 2011, all mobile phones with USB interfaces sold in the EU will have a unified interface of micro-B USB. The interfaces of mobile phones and matching chargers are shown in the figure below: The interfaces of mobile phone chargers have always been varied, from Micro-B USB to MiniUSB, an

[Test Measurement]

Low-cost method to reduce EMC of switch mode power supply (SMPS)

　　If the SMPS switching frequency is designed to be non-fixed and allowed to vary around a certain frequency, its EMC electromagnetic waves will spread out and will not produce large peaks at the switching frequency and its multiples. 　　The range around the center frequency cannot be too large, otherwise the syste

[Power Management]

Low-cost method to reduce EMC of switch mode power supply (SMPS)

Three effective angles to control EMC

　　The increase in clock speeds, coupled with high-frequency buses and higher interface data rates, has made PC board design significantly more challenging. Engineers must look beyond the design of the actual logic on the board and consider other factors that may affect the circuit, including board size, environmental

[Power Management]

Application of EMC Technology in Single Chip Microcomputer System

EMC electromagnetic compatibility includes EMI (interference) and EMS (susceptibility), that is, electromagnetic interference and electromagnetic anti-interference. With the development of intelligent technology, the application of single-chip microcomputers is becoming more and more extensive. Although the single-chip

[Microcontroller]

Engineer: EMC solution based on injection molding machine frequency conversion energy saving system

1 Introduction The matching use of injection molding machines and frequency converters can achieve the advantages of saving energy (the power saving rate can reach 25% to 65%), improving production efficiency and product quality, reducing oil pollution and noise pollution, and extending the service life of machines.

[Power Management]

Engineer: EMC solution based on injection molding machine frequency conversion energy saving system

Popular Resources
Popular amplifiers