Analysis of factors affecting the price difference of LED lamps

Publisher:chaohuangmeitaoLatest update time:2012-06-17 Source: 电子发烧友Keywords:LED Reading articles on mobile phones Scan QR code
Read articles on your mobile phone anytime, anywhere

The LED lighting industry is developing rapidly, and there are many kinds of lamps and lanterns, and the price difference is also quite obvious. There are many manufacturers producing LEDs and LED lighting. Different manufacturers use different quality LEDs, which is an important reason for the difference in LED lamps. Due to the increasingly fierce price war, products with almost the same appearance, structure and function have a price difference of 2-3 times. Many users are confused for a while and don’t know where the price difference comes from. Generally, it is difficult for LED lighting manufacturers that do not produce LED light-emitting tubes to distinguish, let alone consumers.

Therefore, it is better to choose an LED lighting factory that has a good LED production source or has complete LED testing equipment, so that the purchased LED lighting products will be more secure.

Let's take a look at the factors that cause price differences in LED lamps:

1. Brightness

LEDs have different brightness and different prices.

2. Antistatic ability

LEDs with strong antistatic ability have long life and are therefore expensive. Usually, only LEDs with antistatic ability greater than 700V can be used in LED lighting.

3. Wavelength

LEDs with consistent wavelengths have consistent colors. If you require consistent colors, the price will be high. It is difficult for manufacturers without LED spectrophotometers to produce products with pure colors.

4. Leakage current

LED is a unidirectional conductive light source. If there is a reverse current, it is called leakage. LEDs with large leakage current have short life and low price.

5. Lighting Angle

LEDs with different uses have different light-emitting angles. Special light-emitting angles have higher prices. For example, full diffuse angles have higher prices.

6. Lifespan

The key to different quality is lifespan, which is determined by light decay. Small light decay means long lifespan, while long lifespan means high price.

7. LED chips

The light source of LED is chip, and the price of different chips varies greatly. Chips from Japan and the United States are more expensive, while the price of LED chips from Taiwanese and Chinese manufacturers is lower than that of Japan and the United States.

Keywords:LED Reference address:Analysis of factors affecting the price difference of LED lamps

Previous article:LED control applications and their requirements for drive/control solutions
Next article:AAT2868 and AAT2869 Dual-mode High-efficiency White LED Backlight Drivers

Recommended ReadingLatest update time:2024-11-16 16:24

Application Design of MR16 LED Lamp Driver
  MR16 lamps are a type of multi-faceted reflector lamps, widely used in commercial retail and home decorative lighting. Since they usually use halogen filaments as light sources, they have many disadvantages such as low efficiency, high heat generation and halogen capsule handling. However, current LED technology pro
[Power Management]
Application Design of MR16 LED Lamp Driver
A brief discussion on the application of LED in automobiles and the design of its driving circuit
LED is the abbreviation of Light Emitting Diode, which is a semiconductor that can convert electrical energy into visible light with a luminous efficiency of 80% to 90%. Since its development, this semiconductor component has generally been used as an indicator light. With the development of science and technology,
[Power Management]
A brief discussion on the application of LED in automobiles and the design of its driving circuit
Classic analysis of mini2440 LED driver
Linux kernel is 2.6.32.2 Source code analysis tool source insight Preface: It is very simple to operate several GPIO ports in a bare metal machine, just configure the control registers and data registers, but it still takes some effort to implement the same function in a Linux system. The following is
[Microcontroller]
A big discussion on the relationship between the main parameters of LED display
1. Introduction Among the main optoelectronic parameters of LED display screens , there are brightness , viewing angle, uniformity, contrast , refresh rate, etc., and of course some key parameters such as grayscale, brightness level and primary color dominant wavele
[Power Management]
A big discussion on the relationship between the main parameters of LED display
High-efficiency DC/DC constant current power supply LED driver innovative design solution
  1 Introduction   As a new type of light source in the 21st century, semiconductor lighting has the advantages of energy saving, environmental protection, long life and easy maintenance. It is a general trend to replace traditional lighting sources such as incandescent lamps and fluorescent lamps with high-power and
[Power Management]
High-efficiency DC/DC constant current power supply LED driver innovative design solution
Buck regulator turns into smart dimmable LED driver
LEDs are expected to transform the lighting industry with their long life and low power consumption, but a major barrier to their rapid adoption is the high cost of the LEDs themselves. The cost of LED luminaires (complete electric lighting fixtures) varies, but LEDs typically make up about 25% to 40% of the total lum
[Power Management]
Buck regulator turns into smart dimmable LED driver
Discussion on LED Packaging Technology
   There are several types of LED packaging: bracket row packaging, surface mount packaging, and module packaging. These packaging methods are common and commonly used.    1. Conventional existing packaging methods and application fields   Bracket row packaging was the first to be used to produce single LED devices.
[Power Management]
Design of controlling a small LED lamp based on PWM
#include reg52.h #define uint unsigned int #define uchar unsigned char   sbit pwm=P1^0;   uint cycle,high,low; //cycle is the time of one cycle; high is the time of high level; low is the time of low level.   void delay(uint t) { while(t--); }   void main() { cycle=800; while(1) { for(high=1;high =cycle;hig
[Microcontroller]
Latest Power Management Articles
Change More Related Popular Components

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews


Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号