Selection of LCD splicing screens with different brightness-EEWORLD

Collect

Currently, LCD splicing screens are popular products in the display field. I believe that most users are familiar with Samsung's latest 7.3mm ultra-narrow-bezel LCD splicing screen. However, when it comes to the 7.3mm ultra-narrow-bezel splicing screen, there are 700cd/m2 and 450cd/m2. Most people may be confused.

The brightness of the LCD splicing screen is determined by the LCD panel. At present, the panels of LCD splicing screens cannot be produced in China. The first LCD panel production line put into production in China last year, BOE's 6.5-generation line, can only cut LCD panels below 37 inches for small-sized LCD TVs and computer monitors. So no matter which manufacturer you choose to produce the LCD splicing screen, as long as the other party uses Samsung's LCD panel, the hard parameters such as brightness and contrast are unchangeable. So before choosing, you must buy LCD splicing screens of different brightness according to your needs.

700cd/m2 LCD splicing screen VS 450 cd/m2 LCD splicing screen

At present, there is no essential difference between the LCD splicing screens using Samsung LTI460AA04 (700cd/m2) and LTI460AA05 (450 cd/m2) LCD panels in terms of their main applications. However, due to different requirements for large screen brightness in different application environments, the two products have slight differences in specific applications.

Generally speaking, human eyes have a limited tolerance for brightness. If the brightness reaches 700cd/m2 in a small space with poor lighting, human eyes may be burned; however, if the brightness of the display is 450cd/m2 in a large outdoor space with bright lighting, such as a square or street, the image will be blurry to humans. Therefore, the author recommends that users should choose products based on their actual application environment. LTI460AA05 is more suitable for places with poor lighting and limited space, while LTI460AA04 is preferred for wide spaces with sufficient lighting.

In addition, for ultra-narrow LCD splicing screens, the suitable working temperature is within 39 degrees Celsius, and the controllable area reaches the maximum when the relative humidity is 90%, which is the best working state. The higher the brightness of the LCD splicing wall, the more heat it emits. If the heat dissipation is not in place, the display effect will be greatly reduced at the least, and the LCD splicing wall will be damaged in severe cases, affecting its service life. As for users, they should consider their actual operating capabilities when choosing products.

Keywords：Brightness Reference address：Selection of LCD splicing screens with different brightness

Previous article：Simple list of basic knowledge of LED display
Next article：Double dimming mushroom lamp circuit and maintenance method

Recommended ReadingLatest update time:2024-11-16 21:00

The perpetual calendar with key control and temperature written in 51 is displayed on LCD12864

1. The temperature only displays the integer part, which is much simpler. 2. The week was not adjustable before. The problem was that the value was not converted into decimal after reading DS1302. 3. Because the main function always updates the LCD coordinates, the cursor will be updated accordingly. This is not a re

[Microcontroller]

LCD12864 Subroutines

/********************************************************************* Purpose: Create LCD12864 operation library Target system: Based on AVR microcontroller Application software: ICCAVR Version: Version 1.0

[Microcontroller]

[ARM Application] Solve the problem of LCD screen automatically closing and closing without changing the kernel code

It can be implemented in the application. Do not change the kernel driver. Write a small program: #include stdio.h #include fcntl.h #include sys/ioctl.h void keep_LCD_screen(void) { int fd; fd = open("/dev/tty0", O_RDWR); write(fd, "\033 ", 8); close(fd); } int main(void

[Microcontroller]

LCD1602 programming 4-wire parallel port communication source program

LCD 1602 uses 4-wire parallel communication, the connection method is DB4-DB7 connected to P1.4-P1.7; RS: P2.7; RW: P2.6 EN: P2.5; pay attention to the initialization settings. Debugged in Wanli MedWin 3.0 development environment! #include reg51.h /****************************************** *************************

[Microcontroller]

Simulate 8(COM)*8(SEG) LCD driver on EM78Pxx

; /* = ... ; | ; | ;I. LCD scanning principle: | ;Forward scanning: COM on=V CC ,COM off=1/2VCC, corresponding to SEG=1, it outputs VSS, and 0, it outputs VCC. | ;Reverse scanning: COM on=VSS,COM off=1/2VCC, corresponding to SEG=1, it outputs VCC, and 0, it outputs VSS. | ; | ;II. Circuit connection: | ; All COM port

[Microcontroller]

22. Introduction to LCD-FSMC Principle

A little tip: To view the definition of a function, first move the cursor to the function and then press the F12 key. 1. Introduction to FSMC FSMC stands for "Static Memory Controller". After using the FSMC controller, the FSMC_A provided by the FSMC can be used as the address line, and the FSMC_D provided by the

[Microcontroller]

linux2.6.32.2 mini2440 platform transplantation--LCD backlight driver

1.3.1 LCD backlight control principle So far, we have been transplanting under the command line to view the results. In the mini2440/micro2440 development board, the LCD backlight is controlled through the LCD_PWR pin of the CPU. As can be seen from the schematic diagram, it corresponds to GPG4. When the LCD_PWR o

[Microcontroller]

A Practical Hardware Design of Segment Code LCD Driver Circuit

1. Overview There are two commonly used displays in instruments and meters, one is light-emitting diode (LED) and the other is liquid crystal display (LCD). These two displays are low-cost, flexible in configuration, and easy to interface with single-chip microcomputers. The latter has small driving current, low

[Power Management]

A Practical Hardware Design of Segment Code LCD Driver Circuit

Popular Resources
Popular amplifiers