Solar lawn lights mainly use the energy of solar cells to work. When sunlight shines on the solar cells during the day, the light energy is converted into electrical energy and stored in the battery. The battery then provides power for the LED (light-emitting diode) of the lawn light at night. Its advantages are mainly safety, energy saving, convenience, and environmental protection. It is suitable for beautification and lighting of green lawns in residential communities and beautification and embellishment of park lawns.
The structure of LED solar lawn light:
It consists of solar cell components (photovoltaic panels), super bright LED lights (light sources), maintenance-free rechargeable batteries, automatic control circuits, lamps, etc.
LED solar lawn light system composition:
The solar lawn light boost IC can automatically switch between charging and discharging. When the solar charging panel senses sunlight during the day, it automatically switches to turn off the light and enters the charging state. When night falls and the solar charging panel cannot sense sunlight, it automatically switches to the battery discharge state and turns on the light. The solar lawn light boost IC can increase the output voltage of a 1.5 volt rechargeable battery to 3.6 volts.
One set of circuit board IC should be equipped with one No. 5 rechargeable battery to drive 1-7 LED light-emitting diodes; multiple sets of circuit board IC and so on; the integrated circuit and some peripheral components of the solar lawn lamp controller, the main functions include charging circuit, driving circuit, photosensitive control circuit and pulse width modulation circuit, etc. The controller has high conversion efficiency: 80~85% (typical value), which can reduce the power requirement of solar cell panels; low? Start voltage: 0.9V (maximum value); adjustable output current and other characteristics.
LED solar lawn light source advantages:
At present, most lawn lamps use LED as the light source. LED has a long life span of more than 100,000 hours and a low operating voltage, which is very suitable for use in solar lawn lamps. In particular, LED technology has undergone a key breakthrough, and its characteristics have been greatly improved in the past five years, and its performance-price ratio has also been greatly improved. In addition, LED is powered by low-voltage DC, and its light source control cost is low, making it possible to adjust the brightness and frequent switching without adversely affecting the performance of the LED. It can also easily control the color, change the distribution of light, and produce dynamic illusions, so it is particularly suitable for solar lawn lamps.
Solar lawn light source and power system design method has developed rapidly in recent years due to the unique advantages of solar lawn lights. Lawn lights have low power, are mainly used for decoration, have high requirements for mobility, are difficult to lay circuits, and are suitable for sites with high waterproof requirements. These make solar powered lawn lights show many unprecedented advantages.
Previous article:High-speed control solution for large-screen LED displays
Next article:Research on defect detection method based on LED chip packaging
Recommended ReadingLatest update time:2024-11-16 23:38
- Popular Resources
- Popular amplifiers
- MathWorks and NXP Collaborate to Launch Model-Based Design Toolbox for Battery Management Systems
- STMicroelectronics' advanced galvanically isolated gate driver STGAP3S provides flexible protection for IGBTs and SiC MOSFETs
- New diaphragm-free solid-state lithium battery technology is launched: the distance between the positive and negative electrodes is less than 0.000001 meters
- [“Source” Observe the Autumn Series] Application and testing of the next generation of semiconductor gallium oxide device photodetectors
- 采用自主设计封装,绝缘电阻显著提高!ROHM开发出更高电压xEV系统的SiC肖特基势垒二极管
- Will GaN replace SiC? PI's disruptive 1700V InnoMux2 is here to demonstrate
- From Isolation to the Third and a Half Generation: Understanding Naxinwei's Gate Driver IC in One Article
- The appeal of 48 V technology: importance, benefits and key factors in system-level applications
- Important breakthrough in recycling of used lithium-ion batteries
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- Qinheng USB PD and other fast charging protocol power receiving chip CH224 evaluation - the second level configuration test and battery charging test
- MSP-EXP430F5529LP Development Board 005-PWM Library Function + Clock Configuration
- The latest KEE courses for 2020 are out, be the first to make an appointment!
- Share the requirements and characteristics of current detection resistors
- The gap between the actual filter circuit and the simulation is too large
- TI DSP bootloader and online upgrade
- Questions about creating schematic package in Orcad
- EEWORLD University Hall----Live Replay: Dadatong helps you unlock the new generation of ADAS technology
- What are the six axes in a six-axis robot?
- Three-phase sensorless sine wave BLDC drive (MS39549 and MS39545)