Design and implementation of wireless video intercom access control image communication

At present, most of the entrances to residential buildings in small and medium-sized cities are open, which makes it convenient for residents to enter and exit, but also brings many inconveniences and instability to residents' lives. For example, anyone can enter the corridor of a residential building at will, and all kinds of paper advertisements posted on the walls or stairs can be seen everywhere in the corridor, which affects both the hygiene and the beauty of the corridor. The visual intercom access control system can realize the functions of residents' recognition of visitor images and two-way communication.

It just solves many inconveniences in residents' lives and has become an indispensable supporting facility in residential areas. Most of the current video intercom access control systems are wired systems. Although they have the advantages of large transmission capacity and high reliability, wired systems also have their inevitable disadvantages, such as poor flexibility, high installation cost, high construction difficulty and difficult maintenance. The wireless video intercom access control system can be placed at will and can be used immediately after installation, eliminating the trouble of wiring and drilling holes, and will not affect the decoration environment and interior beauty. People can use wireless remote control to automatically unlock the door at any position in the room, avoiding the inconvenience of having to go to a designated location to open the door. Therefore, the study of wireless video intercom access control system to replace the wired video intercom access control system has far-reaching practical significance and high academic value, and can solve practical problems in real life.

At present, foreign research on wireless video intercom access control systems is booming, among which the latest model GB3188 designed by Motorola is a typical representative. This machine has brought efficient and simple access management solutions to many merchants with its outstanding overall design and excellent performance-price ratio, especially to users in industries such as property management, hotel services, construction and manufacturing . However, the disadvantage is that the system does not involve image transmission. Domestic research on wireless video intercom access control systems is mainly moving towards wireless visual. The wireless video intercom access control system designed by Master Cui Zhen of Beijing University of Technology can transmit analog and digital signals in the same channel, saving a set of wireless transceiver equipment and reducing costs. However, the image signal and sound signal are transmitted by analog signals, and only the call signal, unlocking signal, and alarm signal are transmitted by digital signals, resulting in poor sound and image quality, and interference signals. The wireless video intercom access control system designed by Professor Meng Limin of Zhejiang University of Technology realizes the digital transmission of sound signals, but the image signal is still transmitted by analog signals, so the image quality is poor. This paper designs a building wireless video intercom circuit, which uses a single-chip microcomputer as the controller core and connects to peripheral circuits. It transmits video signals through a wireless digital transmission circuit, and can achieve a wireless transmission distance of 50 to 200 meters. The advantage of this design is that it can obtain continuous display of images based on single-shot shooting, and it truly realizes wireless digital transmission of image signals.

1 Overall design plan

The system structure mainly consists of three parts: the host computer system, the slave computer system and the communication system. These three parts together complete the information exchange between the main controller and the sub-controller to achieve the purpose of building monitoring. The main controller and the sub-controller transmit data and commands through the wireless digital transmission module SRWF. This communication model belongs to a one-to-many communication mode.

The main control chip of the main controller is AT89C51. It obtains the room number to be visited through the keyboard. After confirmation, the single-chip machine will control the opening of the video acquisition chip and the buffer chip to work, and send the data to the digital transmission circuit through the serial port communication under the set communication baud rate. The digital transmission circuit then sends the data through the wireless channel. The main control chip of the slave controller also uses AT89C51. It receives the control information and data information of the main controller through the digital transmission circuit and classifies the received data. If it is a communication address signal sent by the host, the slave controller will read the data in the ringing tone storage circuit and send out a ringing tone. Next, it starts to receive the video signal and displays it through the LCD display circuit. The user can decide whether to have further communication with the main controller through the key control circuit.

2 Hardware Circuit Design

2.1 Circuit Design of Main Controller

The main controller circuit is composed of single-chip microcomputer AT89C51, keyboard scanning circuit, drive and digital display circuit, watchdog circuit, wireless data transmission circuit, etc. The hardware circuit principle of the main controller system.

The working process is as follows: First, the keyboard scanning circuit scans the user's key information to obtain the communication address of the slave, and displays the key information through 4 LEDs so that the user can clearly know the slave address he wants to access. The user can confirm and modify the input value by adding, subtracting, and re-entering on the keyboard. When the user presses the confirmation key, the host stores the slave address at this time, turns on the video chip to sample the video signal, and sends the slave address through the wireless digital transmission chip SRWF. After receiving the response signal and ready signal from the slave, the host starts to send data at the set baud rate. Wait for the response signal from the slave every time a frame of data is sent, and send a check frame for each frame of data to ensure the accuracy of data transmission.

2.1.1 Keyboard scanning circuit

The keyboard scanning part uses a 4×4 keyboard, and the scanning level is set through the P1 port. First, one of the lower 4 bits of the P1 port is set to zero, and then the level of the upper 4 bits of the P1 port is read. The lower bit of the P1 port is set to zero, which means that the column line is set low. If a bit is detected as zero in the upper 4 bits of the P1 port, the position of the key can be known through the position of the row and column. There is a jitter problem in the key pressing process. The solution includes hardware encoding keyboard and software encoding. Considering the cost considerations and the high performance of AT89C51, this design uses software encoding to achieve scanning. The keyboard scanning circuit is shown in Figure 2.

2.1.2 LED display circuit

The LED display circuit uses a dynamic display mode, which is composed of a 74LS248 BCD decoder chip and a 74LS138 decoder. The purpose of using 74LS248 is to save I/O port resources so as to control more peripheral chips. The segment selection data of the LED is determined by the segment selection code decoded by 74LS248, and the bit selection data is generated by 74LS138 decoding. When working, the key value is first converted into BCD code, and then sent to the 4th bit of the P0 port, but the overall copy of the P0 port will destroy the data of the bit selection port. At this time, the data of the P0 port needs to be corrected, and the bit selection data is also sent to the 4th and 5th bits of the P0 port through the OR logic operation, and then the corrected data is sent to the P0 port. At this time, there are both segment selection data and bit selection data. To make the displayed data not flicker, it is necessary to use the visual persistence of the human eye to control the time delay between each data display within 10 ms, so that the displayed numbers will not flicker.

2.1.3 Video acquisition and data transmission circuit

The video acquisition circuit is composed of CAMERA 0V 7620 chip and IDT7205. This combination method is adopted because the amount of video data is relatively large, but the working frequency of the single-chip microcomputer is relatively low. If they are directly matched, the two cannot be received normally. Therefore, the buffer chip IDT7205 is added, so that the single-chip microcomputer controls its work to achieve the matching of the data volume and the single-chip microcomputer. IDT7205 is enabled only when the single-chip microcomputer allows reception. If the single-chip microcomputer detects that the VSYN of the video chip jumps up, it will output 1 at the P0.7 port, thereby starting to control IDT7205 to obtain data from the video chip. Before using the SRWF module, the wireless channel, interface type, interface rate, interface parameters, etc. must be set. After the settings are completed, data transmission can be carried out. When the module receives the first data sent by the single-chip microcomputer, it automatically performs wireless network connection and data synchronization. Therefore, the first data will be output from the receiving serial port after a 5-byte time delay, as shown in Figure 2.

[page]

2.2 Circuit design of sub-controller

The sub-controller also uses AT89C51 single-chip microcomputer as the microprocessor. The peripheral interface circuit of the sub-controller system is composed of crystal oscillator, LCD image display circuit, key unlocking circuit, watchdog circuit, communication interface circuit, memory, etc. Hardware circuit of the sub-controller system.

Its working process is: initialize its receiving baud rate and keep in information monitoring state. When receiving the address frame, it will be compared with its own address. If different, discard this frame data and continue to detect. If the same, read the music code stored in the AT24C02 chip, control the speaker to emit music sound through the P2.1 port, and tell the user that a visitor requests to enter the building. When the user presses the answer key on the keyboard, the single chip will send the data received from the wireless digital transmission module to the P0 port for LCD display. When the homeowner sees the image on the LCD, if he knows the visitor, he presses the key to unlock; if he does not know the visitor, he presses the hang-up key to end the video call. The main working chip of the video display circuit is TFT6448B. TFT6448B has its own data latch and does not need to expand the latch chip. After selecting TFT6448B, the control display of TFT6448B can be realized by writing data to the corresponding row, column, control, and data registers of TFT6448B.

3 Software Design

The host is AT89C51 single-chip microcomputer, and the slave is AT89C51 single-chip microcomputer. The data communication baud rate between the host and the slave is set to 9600 B, and each slave has a unique address number to distinguish each slave. The data communication of the single-chip microcomputer is completed by the serial port. Timer T1 is the baud generator. The data transmission format is 1 start bit, 8 data bits, 1 stop bit, and 1 programmable bit (T-B8). Working mode: Set timer T1 to mode 2 and the serial port to working mode 3.

The communication protocol of this system is: the SM2 position of all slaves is 1, and they are in the state of receiving address frames. The host sends an address frame, in which the 8th bit is the address and the 9th bit is the address/data distinguishing mark. The position 1 indicates that the frame is an address frame. After receiving the address frame, all slaves will compare the received address with the address of the local machine. For the slaves with matching addresses, their SM2 position is 0, and the local address is sent back to the host as a response; for the slaves with inconsistent addresses, SM2=1 is still maintained, and the data frame sent by the host is ignored. After the slave finishes sending data, it must send a frame checksum and set the 9th bit to 1 as a mark of the end of the slave data transmission. When the host receives data, it first determines the data reception flag RB8. If RB8=1, it means that the data transmission is over, and compares the checksum of this frame. If it is correct, the correct signal 00H is sent back to command the slave to reset; if it is wrong, the signal OFFH is sent to command the slave to resend the data. If the received frame RB8=0, the data is stored in the buffer and ready to receive the next frame of information. After receiving the response address from the slave, the host checks whether the address matches. If the address does not match, it sends a reset signal; if the address matches, it clears TB8=0 and starts sending data. After receiving the reset command, the slave returns to the listening address state, otherwise it starts to receive data and commands.

4 System Simulation

Draw the circuit schematic in the ISIS 7.1sp2 software environment of Proteus. The next step is to compile the designed program into machine language in the Keil C51μVision2 integrated development environment. Enter the ISIS of Proteus, click the menu "Debug" with the left mouse button, and select "use romote debugger monitor" to realize the connection debugging between KeilC and Proteus. First, double-click the microcontroller AT89C51 in Proteus, and import the .HEX file generated by programming under KeilC into AT89C51. You can click the full-speed simulation run button in Proteus to view the phenomenon. You can clearly observe the level changes of each pin on the chip. Red represents high level and blue represents low level. If the phenomenon is incorrect, debug the program in KeilC step by step and observe the phenomenon in Proteus. If any step is incorrect, modify the program in that section and debug until the simulation is completely successful.

Press the three buttons on the scanning keyboard in sequence. After all three buttons are entered, the data just pressed will be displayed on the digital tube. The numbers will be displayed in the order in which they are pressed. The number represents the room number to be visited, such as 504 means that the owner of room 504 is to be visited.

In Proteus, LM4229 is used to replace the TFT6448B chip in the design. The purpose of the simulation is to obtain the encoding method of image display and the monochrome bitmap display function of the LCD. LM4229 determines whether to read data or read status, or write data or write commands through the levels of the three pins CDWRITE READ. Its data pin is 8 bits, which can directly exchange data with the microcontroller. The P2 port is the control end of the LCD display.

5 Conclusion

The visual hedge circuit adopts the design with AT89C51 microcontroller as the core and SRWF-1, CAMERA OV 7620, IDT7205 and other peripheral chips. The hardware circuit diagram and main program flow chart are given in this paper, and the processing of key technologies in the software and hardware design process is explained. The circuit can fully meet the practical requirements of the building wireless visual intercom circuit for continuous acquisition of image signals, wireless transmission of image signals, display of monochrome bitmaps, and ringing calls. The innovation of this article is to apply low-speed microcontrollers to image signal acquisition with large data volume and short-distance wireless transmission of images. In the design, the real-time processing of image signals will become a direction that needs to be studied in the future.