Research on Improvement of Fingerprint Direction Map

Recommended ContentMore

Open source project More

• Development kit for ST25R3911B high performance HF reader/NFC launcher with 1.4 W output power, VHBR and AAT
• PCF8574
• WeAct-MiniH750-LTDC expansion board
• 【Simulation Model】01-Resistor
• MCP41xxx Digital Potentiometer Verification Board
• Fully integrated stepper motor driver based on L6472
• Digital wall dimmers for halogen and low-power lamps
• 24x16 Matrix Mini
• A complete access control system (schematic diagram + source program)
• Sun Lexian’s LED voice-activated lights

Searched by Users

• MCUISP 5.0.0 is a third-party STC microcontroller download software
• RISC-V Handbook A guide to the open source instruction set
• Circuits Nelson 10th Edition HD PDF
• Download wire and cable current carrying capacity standards
• Cracked version of ModBusPoll.4.3.4+Slave+Cracked version of virtual serial port assistant
• Arduino Graphical Programming Guide
• My own commonly used AD encapsulation library
• Gerber file viewing tool software
• PCB Circuit Resistance Calculator
• VBSCRIP Language Reference

Just Take a LookMore

• EEWORLD University - i.MX Linux Development Practical Guide
  i.MX Linux Development Practical Guide : https://training.eeworld.com.cn/course/5854The first issue - Getting Started with Zero Foundation - 47 episodes The second issue - Kernel Programming - 20 epis
• Encoder Problems
  [backcolor=rgb(222, 240, 251)]I designed an encoder circuit, the circuit is as follows: [/backcolor][backcolor=rgb(222, 240, 251)]Afterwards, when I turned the encoder, there were waveforms on both en
• Introduction to IC Packaging and Testing Process
  This article shares the IC packaging form, packaging materials and process flow, a total of 41 pages, interested parties can take
• TI C6000 Optimization Advanced: Loops are the most important!
  Software Pipelining 1. C6000 Pipeline The processing of an instruction is not completed in one step, it is divided into three stages: fetch, decode, and execute. Putting each stage into an independent
• A zero voltage platform appears on the secondary side of the forward converter, causing large oscillations. What might be the cause? How can I solve it?
  I'm working on a forward converter recently, using RCD for excitation reset, and it's basically working normally. However, when the MOS tube is turned on and off, there is a commutation process betwee
• STM32MP157A-DK1 Review - 5.10 minutes to create a Linux Distro
• DIY a ESP32 game console based on MicroPython
• Getting started with BIT_BAND (bit segment/bit band) and alias area in STM32
• [Xianji HPM6750 Review] RT-Thread SPI Driver and WiFi Networking
• In-depth analysis of the design of a dental chair control system based on ARM embedded technology

Trending Downloads

• Quaternions and 3D Rotations
• MT612X
• Design of small DC electromagnet boost and drive circuit based on SG3525
• Fujitsu 90945 series CAN transceiver program
• Embeded System Design
• Research on sensorless control strategy of permanent magnet synchronous motor in full speed range
• Integrated Circuit Testing Courseware Sharing
• Method for eliminating AC interference noise in audio signal transmission
• A Brief Introduction to Electronic Calculators
• MOS operational amplifier principle design and application_Li Lian

Trending ArticlesMore

• Google's new research on predicting depth of field: Even if the camera and characters are moving, a single viewpoint can synthesize a 3D depth map
• It’s time to sum up 2020
• Microchip announces expansion of SiC production
• Receive your award! The list of winners of the 7.15 seminar is announced
• Low power consumption analysis based on KL16 fingerprint lock
• David Zhao: Challenges of 5G RF Front-End
• Vietnam in the spotlight this year
• The online seminar will start on time at 10 o'clock today!