Self-made 3D connector library: Female-Header-2.00-SMD-32

Recommended ContentMore

Open source project More

• esp32-audio-development-kit: Portable, open source, ESP32-based audio development platform with touch screen and support for Bluetooth and Wi-Fi connectivity
• Relay arc extinguishing circuit
• GK64 left shift
• 【Training Camp】Little self-written clock
• Huanghuai College Lichuang Cup Electronic Technology Competition-1003728A-Zhang Kuohang
• L99SM81V Evaluation Board
• Simple thermometer based on thermistor
• STC8H3K64S2 makes 12864LCD dual-channel voltage and current capacity meter
• Flash driver based on STCF01
• Liuliu smart car

Searched by Users

• PADS VX2. Quick Learning Tutorial
• Modern permanent magnet synchronous motor control principle and MATLAB simulation
• Microcontroller C language programming and examples.pdf
• Synthetic Aperture Radar Image Processing.pdf
• LINUX and UNIX SHELL Programming Guide
• RADIUS Server Introduction RADIUS server supports standard RADIUS protocol
• SIMATIC NET v6.0 OPC SERVER Communication Configuration Instructions
• PCB Engineering: Allwinner A33 original core reference demo sharing 2 DDR3 4-layer design.rar
• A good serial port debugging tool! ! Using the commonly used SPCOMM control
• MPC03-LV motion control card driver

Just Take a LookMore

• Capacitive touch MSP430FR2676 MCU motherboard
  The MSP430FR2676 CapTIvate Touch MCU Board (CAPTIVATE-FR2676) is a simple evaluation board for evaluating capacitive touch and proximity sensors using plug-in sensor boards (sold separately).The MCU b
• 【XMC4800 Relax EtherCAT Kit Review 2】-Building the environment and lighting up the LED
  [i=s]This post was last edited by tdatd on 2019-1-2 11:13[/i] [align=left][align=left]Go to the evaluation application interface[size=7.5pt] [/size][url=https://en.eeworld.com/bbs/elecplay/content/100
• 【GD32L233C-START Review】-Serial port to USB to implement printf printing
  Hardware InterfaceFrom the hardware configuration point of view, USART0 is used .Software InterfaceSerial port initializationSerial port printf redirectionAdd Print InformationConnect USB portInstall
• Common problems in OLED development
  1.Installation There are usually three ways to install OLED:1). Because it is relatively thin, it can usually be glued to the PCB with double-sided tape or foam tape.2). If you have higher requirement
• ECG monitor solution based on DSP system platform
  In recent years, with the increasing aging of society, cardiovascular disease has become the main disease threatening human life, and heart disease has become the disease with the highest mortality ra
• A novice asks about AD copper plating, thank you
• F28335 Memory Map
• Imported project compilation fails
• [Project Outsourcing] Optimize the Raspberry Pi boot time to 5-8 seconds
• How to buy ti boards from Chinese dealers?

Trending Downloads

• CB555CP, Universal Time Base Circuit, Chinese Data
• DDS Design Based on Verilog_HDL
• Design and implementation of video acquisition and processing functions based on ADSP-BF561
• LM324 battery charge detection
• Looking for an AT_command that can support the MT6250 platform
• Static timing analysis basics and applications
• INTEL_82870P2
• A very sophisticated XML implementation library written in C
• Design of IP network telephone terminal based on Nios
• Pulse Width Modulation (PWM) Tutorial

Trending ArticlesMore

• I can miss anything but you, my Maxim serial transceiver~
• Practical | Analysis and application of four common constant current source circuits
• Renesas Electronics Wins "2019 CITE Innovation Award"
• A few pictures to understand how to choose ARM9 core board
• Revolutionizing radar design with electronically reconfigurable GaN power amplifiers
• Power Management IC "BD71850MWV"
• Nature lists these codes, all of which have changed science: Fortran, AlexNet, arXiv, etc.
• In-depth understanding of Linux kernel process sleep (Part 2)
• NVIDIA Lecture Room | What is Graphics Analytics?
• Why is Tesla not short of chips?