Discussion on the implementation of centralized monitoring in Baishan cascade hydropower plants

Recommended ContentMore

Open source project More

• SlimSASCEMx8_EVM
• [Tuya Smart] zigbee&Bluetooth multi-mode gateway
• Intelligent car based on Liangshan School
• MCU core board (328P)
• ALP electric guitar built-in headphone amplifier
• Open source USB2.0 high-speed analyzer
• AT32F435mini flight control
• DER-232 - Ultra-Low Profile (15.4 mm) 65 W Adapter
• CN0214
• #The 8th LiChuang Electronic Competition#Voice Clock

Searched by Users

• PyTorch official tutorial Chinese version
• Content: Simulink nonlinear module simulates sinusoidal signal through new loop function
• A program to initialize the USB camera
• Digital Signal Processing C Language Programming Set.pdf
• J-LINK V8 firmware burning guide, burning source program, all the programs required for burning
• Support packages for STM32F4 series
• vb decompilation tool, can decompile part of vb5 or vb6 code
• Mitsubishi PLC from entry to mastery, detailed explanation of the road to learning PLC (with various illustrations) free download
• GX Simulator6-C Chinese version simulation software
• Free download of basic electrical engineering courseware

Just Take a LookMore

• Classification of RFID readers and their advantages
  RFID readers are an indispensable part of the application system. Whether they are correctly selected will affect whether the customer project can be successfully implemented and the cost of implement
• [Repost] Correctly select low noise amplifier
  [align=left][color=rgb(25, 25, 25)][font="]Currently, discussions about low-noise amplifiers often focus on RF/wireless applications, but in practice, noise also has a significant impact on low-freque
• NTC thermistor driver for MicroPython
  Micropython's NTC thermistor driver, assuming the nominal value of the NTC is 10K, is pulled up to vcc through a 10K resistor R1, and the temperature is calculated after ADC sampling.The default B val
• How does Cyclone2's ep2c8 provide clock to external ADC?
  I want to provide a clock to an external high-speed ADC. The FPGA clock is provided by an external crystal oscillator connected to CLK0. Can it be output directly from the PLL_OUT pin? How should the
• Comparison of Autoliv 2nd and 3rd generation night vision cameras
• If I use a battery to power a DCDC circuit, how can I be sure that the battery has enough power?
• Standard USB keyboard data packet
• 【Small home weather station】+ Hardware design, board proofing
• Forever power_A tiny device that turns your universal power bank into an uninterruptible power supply
• 【NUCLEO-WL55JC2 Review 2】Introduction to NUCLEO-WL55JC2 Development Board

Trending Downloads

• element14 BeagleBone Black User Manual
• Analog Circuit Basics Tutorial Book Software is relatively small
• MSP430 (Chinese) [Comparator_A] realizes voltage, current, capacitance and resistance measurement
• Design method of quasi-resonant flyback converter based on L6565.pdf
• Journal article: Military applications of CMOS image sensor technology
• Chip failure analysis methods and steps
• Digital Circuit Basics Test Paper 4 Answers.doc
• Siemens PLC step 7 v5.4 programming manual.pdf
• Electronic Design Automation and IC Design (Higher Education Publishing Du+2004)
• Application of WB Language and MCS-51 Single Chip Microcomputer in Master-Slave Communication

Trending ArticlesMore

• The world's lowest power consumption WiFi RKi6000 smart product debuts at MWC
• Core Course | Analyzing how ICV LVS Explorer can accelerate full-chip LVS convergence
• Do you need a high voltage, high efficiency positive to negative converter?
• How 3D Hall Effect Sensors Enable Precise Real-Time Position Control in Autonomous Systems
• The low-key LoRa has another big move!
• Useful information | Understanding analog signals in PCB
• Learn about PI's new PowiGaN switching power supply IC and answer questions to win prizes!
• Sony's latest sensor and the technology behind it
• These movies may not win an Oscar, but they will give you a blast!