[Data]-JIS B1086-1998 Widening test on nuts.pdf

Recommended ContentMore

Open source project More

• Phase/serial input 2-phase stepper motor driver IC——TB67S213FTAG
• WCH-DAPLink Femto Mini ARM Debugger
• Tuya four-way relay switch
• USB multi-port simultaneous charging desktop
• DAP miniWiggler (Infineon Downloader)
• D/A and amplifier module
• MC3172 base plate
• [Training Camp] Small clock developed based on OpenHarmony Hongmeng operating system
• dc-dc19-12-23
• Pure PCB ruler series

Searched by Users

• DLT645 Electricity Meter Software
• Computer motherboard repair is not a big deal
• Download cpuview graphical microcontroller programming software
• STM32F407 drives EC20 module MCU source code, for your reference
• PLC-Mitsubishi PLC programming software GX Developer 8.86 (Chinese version)
• Power 645 protocol message generator
• Cadence High-Speed ​​PCB Design Practical Strategy
• The best GBA emulator software (Monika Chinese version) is strongly recommended to use this emulator to emulate \"GBABOX\" and \"GBAHRD\"
• 51 single chip microcomputer is very simple - Introduction to Proteus and assembly language and examples
• NCP1654——ON Semiconductor Power Factor Control Solution

Just Take a LookMore

• [Mill Edge AI Computing Box FZ5 Review] First experience with "object detection"
  The two examples that come with edgeBorad, image classification runs smoothly, and now let's run "image calibration" also known as "object detection". This is an application for detecting screws and n
• How do you determine the phase of voltage and current?
  How do you determine the phase of voltage and current?Output sine wave 0-50V, maximum output current within 25mA, output power 1.5W. Voltage signal VF0, current signal IF0, when VF0 and IF0 are in pha
• Can four 16-bit DDR3 chips be designed using a 6-layer PCB?
  I would like to ask, if 4*16bit DDR3, front and back mounting layout, using 6-layer PCB design, what should the reasonable stacking structure be? Is there any risk in 6 layers? Thank you.
• CC2530 and CC2592 detailed introduction
  This application report describes pairing the cost-effective SimpleLink ZigBee CC2530 wireless networking MCU with the SimpleLink CC2592 extender to improve receiver sensitivity, increase the total li
• Python syntax does not work with multiple spaces.
  [i=s]This post was last edited by kangkls on 2018-6-30 15:10[/i] I was very lucky to get a PYboardCN V2. I tried a few programs with the serial port and it was very convenient. I wanted to save it as
• Schematic diagram of BLDC (PMSM) controller based on STM32103x
• Raspberry Pi Pico Documentation
• 【Beetle ESP32-C3】Hardware Analysis
• Design Method of AC/DC PWM Flyback Converter
• Design of Accelerometer Temperature Control System Based on DSP

Trending Downloads

• Personal 3D connector library: Female-Header-2.54-SMD-10
• Cmake dynamic library test
• motion_driver_6-1
• Design of broadband and high isolation base station antenna
• crpowtech-LED driver solution PT4207
• Research on consistency method of target information transmission in air defense missile system
• Labview Forum - Camera acquisition program based on Labview
• DS1010
• Touch and input sensing technology design solutions
• MULTILAYER MODULE (classic)

Trending ArticlesMore

• Heavy rain! A direct look at the current situation of Zhengzhou electronics factories and wafer fabs
• Apple has become a well-deserved giant in the chip field
• The Internet of Things
• Xinwang Microelectronics won the "5th Lingxuan Award for Excellence in Integrated Circuits"
• Toshiba Welfare丨Explore the Secrets of Photorelays——Free Application for Evaluation Board TLP3107
• Synopsys has settled in Zhihu and invites you to start the "core" journey together!
• Dialog Audio Codec and Amplifier Product Family
• ARM SMMU Study Notes
• [Shishuo Design] How to accurately control system temperature? Here is a "guide"!