A software made by DELPHI that can directly capture the screen and write and draw on it. Please correct me.

Recommended ContentMore

Open source project More

• TWR-KL28Z72M: Kinetis ^® KL28 MCU Tower ^® System Module
• Snake design based on UCOS system ARM9 hardware platform
• IOTW-001(ESP8266) module
• KIT33883FRDMEVM: Freedom platform for MC33883 H-bridge gate driver
• Matrix LED Controller ASL5015SHN Evaluation/Development Board
• OM13489: Universal 16-bit general-purpose IO daughter board for Fm+ development board
• Reflow soldering thermostat
• 74-LOGIC-CLOCK
• CN0320
• C3024476_CH348Q chip solution verification board

Searched by Users

• Modbus Debug WizardModbus Debug Wizard
• PLC-Mitsubishi PLC programming software GX Developer 8.86 (Chinese version)
• CodeVisionAVR cracked version
• CUDA Chinese Tutorial
• Commonly used encapsulation libraries for AD software
• CAD custom fill patterns 709 types.rar
• Serial port debugging assistant (CM hardcover version V3.8.1)
• Genetic algorithm MATLAB implementation source code
• SD card protocol V2.0 (full version)
• Download the latest proteus component library

Just Take a LookMore

• RS-485 communication interface encoder
  CUI Devices' RS-485 encoders use a fast position safety protocol that allows the encoder to actively respond to position within one byte. Referring to the OSI model application layer of the RS485 stan
• FPGA Implementation of Fully Parallel FFT
• RT-Thread has been ported to W600
  The IoT operating system RT-Thread has been ported to the W600 system, and you can run mpy on the W600.[size=14px][url=http://docs.thingsturn.com/development/rt-thread/start/]W600 RT-Thread (trial ver
• MakeCode now supports STM103
  MakeCode now supports STM103, which is for the bluepill low-cost development board using the STM32F103C8.
• Please help me with the trip zone configuration of TI's 28034!!!
  I am a newbie, please help me analyze the reason! !Regarding the configuration of trip zone, when TZ time is triggered, all three PWMs are set to low. After initializing the three PWMs, it is found th
• EV-HC32F460_1. Unboxing
• The input capture of stm8s cannot enter the interrupt. Please help? ? Thank you!!!
• 10 bit serial controlled analog to digital converter (MS1549)
• [NXP Rapid IoT Review] I2C Program Small Bug
• EEWORLD University Hall ---- e-Network Lecture Hall

Trending Downloads

• Changing displayed data after keyboard input by using ds12887
• Firewall Technology
• Design and simulation of a new multi-channel digital signal optical fiber transmission system
• EEPROM_Reader/Writer
• Design specification for sawtooth water intake head
• PI5V330 pdf datasheet (Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux )
• Large Icon Frame
• IRF Field Effect Transistor (IRF)
• Control of tooth arrangement robot based on multi-manipulator
• MM74HC4066

Trending ArticlesMore

• Easter Egg丨This is an invitation letter, please check it (don’t miss the Easter Egg inside)
• “Not inferior to GPT-4”! Baidu’s most powerful model was released, and we tested it for the first time
• Infineon Technologies provides secure and convenient mobility solutions for smart cities
• Is demand reaching a turning point? 70% of Taiwan's top 10 semiconductor companies have seen a decline in performance
• A 6.1-magnitude earthquake occurred in Taiwan, and semiconductor companies responded
• MOTO G5 released, what did Lenovo get for $2.9 billion? 丨MWC 2017
• List of the largest domestic chip companies
• The official arrival of the wireless communication era
• Jen-Hsun Huang: If I could go back to 30 years old, I would not start Nvidia
• How to quickly get rid of the "technical newbie" hat - teach you how to play with the RZ microprocessor series in five days · STEP 5