2 mm Type D, 176 Signal Contacts, 8 Rows, Straight
•
•
•
•
•
•
•
•
HSHM Series
Up to 5 Gb/s data rates
Low crosstalk at high frequencies
50/100 Ω (single-ended /differential) impedance
Modular/scalable format IEC 61076-4-101
101 mated lines per linear inch
Four integrated 8.25 A power contacts
Integrated guide pin
End-to-end stackable with 8 row 3M
™
MetPak
™
HM
and HSHM headers
• See the Regulatory Information Appendix (RIA) in
the “RoHS compliance” section of
www.3mconnector.com for compliance information
Date Modified: November 8, 2010
TS-2015-B
Sheet 1 of 3
Physical
Insulation:
Material: High Temperature Thermoplastic (LCP)
Flammability: UL 94V-0
Contact:
Material: Copper Alloy
Plating: See Ordering Information
Performance
Mechanical:
Normal Force (Nominal): 0.57 N [58 g] Signal, 0.74 N [75 g] Shield
Engagement Force (Nominal): 0.32 N [33 g] Signal, 0.22 N [22 g] Shield
Separation Force (Nominal): 0.20 N [20 g] Signal, 0.20 N [20 g] Shield
Wipe (Nominal, Shortest Contact): 2.67 mm [0.105 in] Signal, 1.57 mm [0.062 in] Shield
Mate/Unmate Cycles: 250
Application: This module is suitable for stand-alone use. (Refer to IEC-61076-4-101)
Electrical:
Data Rate: 5 Gb/s
Characteristic Impedance: 50
Ω
Single-ended, 100
Ω
Differential
Current Rating (Fully Loaded): 1 A @ 70° C Signal
Insulation Resistance: 10
4
MΩ @ 100 V
DC
Withstanding Voltage: 750 V
rms
Environmental
Temperature Rating:
-55° C to 125° C
UL File No.: E68080
MetPak is a trademark of 3M Company.
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M
™
MetPak
™
HSHM Press-Fit Header
2 mm Type D, 176 Signal Contacts, 8 Rows, Straight
49.85
1.963
Pin positions
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
HSHM Series
2.00
.079
2.00
.079
ROW I
ROW H
ROW G
ROW F
ROW E
ROW D
ROW C
ROW B
ROW A
ROW Z
2.00
.079
2.00
.079
18.00
.709
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
21.40
.843
15.60
.614
Interstitial
ground
contacts
Shield positions
48.00
1.890
denotes shield column (tail only) omitted for the
row differential pair part
5.00
.197
Signal
contacts
1.50
.059
DIM A
13.40
.528
HSHM-HXXXXX-8XPX-XXXXX
REV X
XXYY
4.50
.177
DIM B
DIM C
DIM A = Pin mating length
DIM B = Shield tail length
DIM C = Pin tail length
Coaxial, column differential and stripline configuration
shown with protective caps*
HSHM-HXXXXX-8XPX-XXXXX
REV X
XXYY
mm
(Inch)
Tolerance Unless Noted
mm
0
±3
0.0
±0.3
0.00
±0.13
( ) Dimensions used for
Reference Only
Row differential configuration
shown with protective caps*
* Caps to be removed after press-fit installation process
Ordering Information
HSHM-H176DPWRX-8CPX- XXXXX
High Speed Option:
4 = Coaxial, column differential and
stripline (75
Ω)
applications
5 = Row differential applications
(rows I and Z not loaded)
Plating μm [ μ” ]:
TG30 = 0.76 [30] Min. Au Contact Area
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Standard Option
TG30L = 0.76 [30] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
TG50 = 1.27 [50] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
TS-2015-B
Sheet 2 of 3
Tail Length:
1 = 4.4 mm pin and 3.5 mm shield
2 = 2 mm pin and 2 mm shield
Standard Configuration
DIM A = 5.3 mm for rows A through H
For non--standard configurations contact sales representative
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
MetPak
™
HSHM Press-Fit Header
2 mm Type D, 176 Signal Contacts, 8 Rows, Straight
HSHM Series
12.00
1.00
2.00
6.00
2.00
1.00
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
H G F E D C B A
Ø
2.00
+0.05
0
Ø
0.10 A B
4.00
Ø
2.35
+.05
-.03
Ø
0.10 A B
Ø
DIM. D
Ø
0.10
M
A B
4.00
48.00
Plated thru holes
H G F E D C B A
14.00
B
A
Recommended PCB hole mounting pattern for
coaxial, column differential and stripline applications
Recommended PCB hole mounting pattern for row
differential applications
(Same geometry as left view without the ground vias)
Hole Plating Table mm
Finished Hole Dia.
0.457 - 0.559 [.0180 - .0220]
Cu. Thickness
0.025 - 0.045 [.0010 - .0018]
SnPb Thickness
0.008 -0.018 [.0003 - .0007]
Drilled Hole Dia.
0.584 - 0.625 [.0230 - .0246]
TS-2015-B
Sheet 3 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.
3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
We are working on a field environmental monitoring project, where the communication terminal and data acquisition terminal communicate via 485. The power supply and 485 signal line share a cable.
I wo...
[i=s]This post was last edited by fish001 on 2020-2-6 22:22[/i]1. Audio:DSP-side interface: MCBSP (multi-channel buffered serial port) MCASP (multi-channel audio serial port)Codec chip: AIC23, AIC13, ...
Special note: I got the development version for more than a month, but I didn't leave it there to collect dust. I have been researching and developing, but I haven't published any work yet because I l...
See that Nyquist sampling theorem is defined as follows:[Nyquist sampling theorem : To restore the original signal from the sampled signal without distortion, the sampling frequency should be greater ...
IT Home reported on May 31 that Xiaomi Community released the MIUI development version internal beta update notes yesterday-On May 30, MIX FOLD released the development version based on Android 12 fo...[Details]
The steering gear, also called servo, was first used on ships to achieve steering functions. Since its turning angle can be continuously controlled by a program, it is widely used in various joint ...[Details]
Overview
In order to provide users with reliable communication guarantees, the wireless network of a mobile communication system must meet appropriate performance indicators. Coverage, capacity, ...[Details]
Protocol decoding is a very practical function of the oscilloscope. Many engineers fail to achieve the desired results because they are unfamiliar with the operation or set the parameters incorrect...[Details]
As semiconductor process technology develops towards the nanoscale, microelectronics technology has entered
the SoC
(system-on-chip) era and continues to develop in the direction of high reli...[Details]
Orifice flowmeter has the characteristics of simple structure, easy maintenance, stable performance, etc., and is widely used in process control and measurement in the fields of petroleum, chemical in...[Details]
The power circuit of a digital camera includes I/F power, lens drive motor power, LCD power, backlight power, etc. How to optimize the design of these power supplies is related to the key features o...[Details]
The sudden outbreak of the COVID-19 pandemic at the turn of the Year of the Rat cast a heavy shadow over the Chinese land and also gave all citizens a very vivid lesson in crisis management. The ou...[Details]
The company needed to use a touch screen on the existing equipment. The display size was 15 inches, so I bought a 15-inch 4-wire resistive screen from Taobao, with a Windows driver. The after-sales se...[Details]
Recently, OnePlus officially announced that the OnePlus 8 series now supports the 90Hz high frame rate mode of the "Peace Elite" mobile game! Now, you can enjoy a smoother and more exciting gam...[Details]
Regarding the 8 working modes of the STM32GPIO port, let us first raise some questions? What if the STM32 GPIO port needs both input and output? 1. Floating input mode The red part in the above ...[Details]
When using MOS tubes to design switching power supplies or motor drive circuits, most people will consider the on-resistance, maximum voltage, maximum current, etc. of MOS, and many people only consi...[Details]
On September 26, Huawei held a domestic launch conference for its 2019 flagship mobile phone Mate 30 series. At the conference, Huawei released the second-generation smartwatch, which can answer call...[Details]
On October 21, 2024, Ji Guanglin, Executive Deputy Secretary-General of the National Vanadium Titanium Industry Alliance and Dean of the Vanadium Titanium Economic Research Institute, and Zhang Jia...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
