Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
The design of high-end electronic ballasts has always been a common task in the lighting industry . Many engineers have spent a lot of time and energy on circuit design and a lot of design - improveme...
[i=s] This post was last edited by Digital Leaf on 2019-5-12 20:48 [/i] [size=4] According to the plan, I should have finished chapters 7 and 8 this week, but when I was actually operating the routine...
The earliest old-fashioned steam ovens used a float switch to detect the water level. The float switch uses the buoyancy of the float to drive the float, and the magnet drives the reed switch to achie...
[i=s]This post was last edited by Lam.lin on 2022-3-31 14:16[/i]Take MPS's MP8007 non-isolated solution as an example, Vin=48V, Vout=12V;Is the following understanding correct:① With VSS as the refere...
The following is a sampling circuit of a residual current detector for an IT power distribution system. It was copied from someone else's board. The circuit and device parameters in Figure 2 have been...
There is not much difference in developing programs for different microcontrollers. If you spend too much time on the programming language of 89c51 and feel that you cannot learn the programming langu...
According to Taiwanese media reports, due to rumors that SMIC may face US sanctions, the mainland's wafer foundries were required by the government to give priority to supplying production capacity t...[Details]
The system uses the most common USB camera, the main chip is Vimicro ZC0301P. One of the features of this camera is that it can implement hardware JPEG encoding. The key points of its driver writing ...[Details]
On December 24, the Shanghai Intelligent Sensor Industrial Park kick-off meeting and key project signing ceremony was held in Jiading Industrial Zone. 39 support policies were released and 32 key pro...[Details]
1. PIC1 microcontroller programming (master control sending) LIST P=16F876 #INCLUDE P16F876.INC CBLOCK 0X24; Reserve three bytes for display COUNT; used as a counter or register ENDC ORG 0X0000 ...[Details]
1. Overview: In recent years, with the rapid development of digital signal processing technology and the continuous emergence of new theories and algorithms, coupled with the overall improvement in...[Details]
In recent years,
the gradual increase of nonlinear loads in
the power
grid is a common trend in the world, such as variable frequency drive or thyristor rectifier DC drive equipment, com...[Details]
Introduction For battery packs designed into HEV, PHEV and EV powertrains, one of the key factors in achieving high reliability, performance and long life is the electronics used in the battery mana...[Details]
First release! Invitation letter to the 2022 Western Digital Economy Expo Time: June 16-18, 2022 Address: Xi'an International Convention and Exhibition Center Theme: Digital empowerment and intelli...[Details]
NXP’s WLAN7207H front-end module combines outstanding Wi-Fi 6 and Bluetooth performance with product design features to enable high-performance smartphones
Shanghai, China – ...[Details]
0 Preface
In recent years, as people pay more attention to environmental issues, the earth's demand for clean energy has become higher and higher. Our company has been committed to the research...[Details]
Preface With the improvement of automation and the networking of information, more and more measurement and control points and measurement and control parameters are required, making an automatic con...[Details]
ZHIYUAN Microelectronics
ZSB101A uses Nordic nRF52820 SoC to provide extended range low-power Bluetooth connectivity in space-constrained applic...[Details]
The KEIL CX51 ANSI C compiler supports all classic and extended 8051 device models. Compiler extensions provide full access to all CPU resources and support up to 16MB of memory. KEILCX51 generates...[Details]
Enter address_type:address in the Memory window to see the variable with the correct address.
Add the module name to be viewed in debug～perfermance analyzer, and then view～perfermance analyzer
wind...[Details]
Abstract: A programmable filter with controllable amplifier is designed based on single-chip microcomputer. The controllable amplifier part is based on the controllable amplifier PGA203 to realize ...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
