EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202AG-00-6651-B

Description
Fixed Resistor, Thin Film, 0.25W, 6650ohm, 100V, 0.1% +/-Tol, 300ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202AG-00-6651-B Overview

Fixed Resistor, Thin Film, 0.25W, 6650ohm, 100V, 0.1% +/-Tol, 300ppm/Cel, Surface Mount, 0202, CHIP

B0202AG-00-6651-B Parametric

Parameter NameAttribute value
Objectid1579356505
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance6650 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient300 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Open source KiCad EDA Chinese data collection and compilation
Preface: Recently, there have been many discussions on KiCad software on the forum. I looked it up online and found the following article, which is quite detailed. Netizens who are interested in KiCad...
okhxyyo PCB Design
How to connect a passive crystal oscillator to an active crystal oscillator?
The circuit board was developed by someone else in the early days, but now I can't find the person who developed it. I want to replace the passive crystal oscillator with an active crystal oscillator ...
巫毒猫 MCU
How to modify the pin port of MSP430F5529
Hello everyone! I am using the MSP430F5529 development board and burning the " singlePWM project " provided by TI . The code uses the P2.0 port and I read the board schematic. I want to change the PWM...
闵丨大 Microcontroller MCU
How about Xunwei's 4412 development board?
Dear embedded system veterans, I have only played with cortex M-level microcontrollers such as STM32 and TM4. I don't know Linux and have never touched cortex A-level processors. Recently, I want to p...
lingking Embedded System
Test and Measurement - Oscilloscope Vertical Resolution
[i=s]This post was last edited by Micsig on 2019-12-17 14:12[/i]Vertical resolution concept The first step in measuring analog signals with a digital oscilloscope is to use an ADC (analog-to-digital c...
Micsig麦科信 Integrated technical exchanges
Essential for battery-powered system designers: TI's battery management technology selection course
TI's battery experts have decades of experience. Our battery scientists work to deliver cutting-edge solutions for new battery chemistriestechnologies, from charging, gauging, monitoring to protection...
arui1999 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号