Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
Receiver
100
3
4
+3.3V
OE or NC
10nF
1nF
1
6
10nF
100
3
4
Receiver
OE or NC
2
5
OE or NC
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Image Storage and Display System Based on SDRAM
F PGA sounds like a boring subject, but if you really understand it and use it, you will find it very interesting. Congratulations to our two students f...
In the official history of the MSP430 microcontroller, there are programs that use serial port interrupts to send characters and strings, but the portability is not high. I have written two functions ...
In today's society, people have higher and higher requirements for the quality of life, and traditional home appliances can no longer meet people's needs, so the concept of smart home appliances has q...
I recently used the STM8L series chip for a project. During the compilation and download process in IAR, a problem occurred. It displayed "SWIM error ". I searched Baidu for a long time and found var...[Details]
u-boot is a Bootloader commonly used in embedded systems.
Bootloader Introduction
Bootloader is a concept that you will inevitably encounter when doing embedded development. It is an im...[Details]
In industrial production workshops, PLCs are widely used in all aspects of automation control. With the construction of intelligent factories, many PLCs are still in an information island state. No...[Details]
Looking around the world, the most popular trend right now is undoubtedly
low-carbon
and environmental protection. As a renewable energy source, solar energy is naturally a representative of ...[Details]
The isolated flyback
power supply
shown in the figure
is designed around the LNK564DN (U1) of the LinkSwitch-LP product family. It can output 5 V/350 mA (1.75 W) over a universal input volt...[Details]
Multiple-input multiple-output (MIMO) technology provides the possibility of increasing the data transmission rate for a single user by transmitting two or four data streams using multiple antennas...[Details]
Today, OPPO held an online press conference and brought a new product, K9S, but it also had another purpose, which was to announce the Double Eleven discount strategy. A large number of its pro...[Details]
Climate change and resource scarcity have become global trends. Under the general trend of global energy conservation and emission reduction, seeking clean energy and improving energy efficiency have...[Details]
A gas sensor is a converter that converts the volume fraction of a gas into a corresponding electrical signal. The detector head conditions the gas sample through the gas sensor, usually including ...[Details]
With the development of social life, people's requirements for current printing and dyeing products are getting higher and higher, especially for cloth and packaging shells, so the requirements f...[Details]
Machine vision has long been used in industrial automation systems to improve production quality and yield by replacing traditional manual inspection. From pick and place, object tracking to metrolog...[Details]
On March 21, the energy management system of the software product "Solar Parabolic Trough Thermal Power Generation Calculation Software V1.0" independently developed by Huadian Engineering (Group) Co....[Details]
Abstract: This paper describes an automatic control system for a greenhouse. The system uses Luminary's LM3S102 processor and a streamlined TCP/IP protocol stack to build an embedded Web server to...[Details]
The PTS526 series long life version is designed for home automation, IoT devices, etc. and can continue to operate for the life of your product.
WALTHAM, Mass. — February 22, 2022 — ...[Details]
The domestic automotive
laser radar
industry is experiencing an explosive growth period, at least for the leading companies. Recently, RoboSense and Hesai, two listed laser radar companies,...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
