Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
Disadvantages of passive filters: poor load capacity, no amplification effect, unsatisfactory characteristics, shallow edges, and mutual influence of various levels.
RC Filtering
1. Selection of C val...
[i=s]This post was last edited by Digital Leaf on 2021-10-6 18:25[/i]The evaluation of ART-Pi has ended, and I have been able to keep the board, so I can start tinkering with it without any worries.
T...
ADI MEMS promotes the development of inclination monitoring. Answer the questions to win prizes! Let's start~Click here to enter the eventTilt sensing uses the gravity vector and its projection on the...
[size=4]Power supply and clock are extremely critical links in the entire system design: if the power supply is unstable or incorrect, the system will work unstably at best, and the chip will be burne...
[i=s]This post was last edited by donatello1996 on 2021-2-19 20:21[/i]During the Spring Festival holiday, I learned the basic usage of the VIVADO development environment and the basic syntax of the Ve...
Other people buy cars to drive, but we buy cars to dismantle. Recently, we learned some methods to dismantle the headlight assembly of a car, so we also took out the BMW 5 Series B48 of our colleag...[Details]
AC-DC LED applications with power above 50 W are widely used in street lighting and high-power area lighting. Different LED solutions can be used in the power range of 50 W-150 W or 100 W-200 W. As...[Details]
Recently, Apple officially released the new iPhone 14 series. In addition to the regular hardware upgrades, there is also a very important function update - satellite communication. What's more power...[Details]
With the development of autonomous driving and connected car technology, in-vehicle networks are developing rapidly, driving the development of the automotive industry. It needs to support more fun...[Details]
The automotive electronic control system follows the basic logic of conventional control systems, including three major links: perception, control, and execution. The sensor is the perception unit fo...[Details]
The design of speech recognition system based on AVR single chip microcomputer, the system uses AVR single chip microcomputer as the control core to realize the recognition and control of human spe...[Details]
Ultrasonic four-channel ranging: Ultrasonic ranging is implemented in three major parts:
One is the 12864 LCD driver with font library:
code show as below:
//////////////////12864 Driver/////////...[Details]
From a global perspective, infrared thermal imagers have been widely used. Since infrared technology can meet military requirements more comprehensively, it is also one of the key development focuse...[Details]
Project Introduction With a history of more than 170 years, the French company Lafarge is currently the world's largest cement manufacturer. Since 1994, Lafarge has been committed to developing a part...[Details]
Generally speaking, compared with traditional single-chip microcomputers, AVR has made great improvements in terms of structure, functional components, performance and reliability in addition to bein...[Details]
Flowmeter is a kind of instrument used to measure the flow rate of fluid in pipes or open channels. It was successfully manufactured in the 19th century and is widely used in various fields. Flowme...[Details]
Adding digital management to lighting systems Outdoor lighting is usually controlled by manually operated mechanical switches to turn the lighting system on or off. To save energy, you may not want t...[Details]
describe
The LT®6200/LT6201 are single and dual ultralow noise, rail-to-rail input and output, unity-gain stable operational amplifiers with 0.95nV/√Hz noise voltage. These amplifiers combine ver...[Details]
On July 4, Xiaopeng City NGP engineering test version crossed the downtown area of Guangzhou, with zero takeovers in the entire 26 kilometers. A few days ago, He Xiaopeng drove the Xiaopeng P5 on...[Details]
With the continuous improvement of people's living standards, the demand for high-performance water heaters continues to rise. According to market surveys, there are currently two types of electric w...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
