Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
First, let me introduce this peripheral:The real-time clock (ERTC) is an independent BCD timer/counter. The ERTC provides a calendar clock and a programmable alarm interrupt.Two 32-bit registers conta...
The SEK-SVM40 evaluation kit includes a VOC sensor SGP40, a humidity sensor SHT40, and a microcontroller that can output VOC index, relative humidity, and temperature via an I2C or UART interface.
The...
Instrument Basics Tutorial Series - Signal Generator : https://training.eeworld.com.cn/course/4778What is a signal generator? What are the types of signal generators? What are the characteristics, per...
I just got the board today. I was almost disqualified because I was a substitute. I still want to thank the staff. Let's take a look at the packaging first.The whole box is very large, and the Mier lo...
Temperature sensor + I2C + serial port + PC host (pyserial) example
The examples are a bit messy, mainly for learning:
Temperature sensor DS18b20, E2PROM, I2C, serial port reading and writing, PC host...
PCB circuit board is a necessary circuit board for equipment and electrical appliances, and is also a necessary carrier for software implementation. Different equipment has different PCB materials. Th...
The STM32C8T6 sends control signals to the motor driver, which controls the stepper motor. Motor drive: Control the rotation of a stepper motor using a PWM signal and a direction signal. The speed of...[Details]
2 Theoretical research on microresistance test
This chapter mainly studies the relevant basic theories of high-precision microresistance tester.
Resistors can be divided into high resistors (...[Details]
On August 29, Star Semiconductor released its 2021 semi-annual report, stating that in the first half of 2021, the company achieved operating income of RMB 718.9367 million, an increase of 72.62% ove...[Details]
When Omar Badar learned that his friends were on the front lines of the COVID-19 fight, using 3D printing to make face shields for healthcare workers, he came up with an idea. “Extraordinary times ...[Details]
On January 28, a 15GW N-type ultra-low carbon high-efficiency heterojunction cell and 15GW high-efficiency solar module project with a total investment of about 15.2 billion yuan was established in...[Details]
This article introduces two TD1514A
amplifier circuits designed by Philips for digital audio
as the dual-channel amplifier circuit of this Hi-Fi combination (as shown in the figure be...[Details]
EPC has announced the EPC2221, a common-source dual-channel gallium nitride field-effect transistor rated at 100 V, 58 mΩ, and 20 A pulse current. It can be used in lidar systems for robots, surveill...[Details]
On January 21, the reporter learned from Northwestern Polytechnical University that the research group of Professor Wang Xuewen, a professor and doctoral supervisor at the Institute of Flexible Ele...[Details]
int bar( int a, int b, int c, int d, int e, int f, int g ) { int array2 ; array2 = a + b; array2 = b + c; array2 = c + d; array2 = d + e; array2 = e + f; array2 = f + g; array2 = g + ...[Details]
Synopsys has been honored as OPPO’s outstanding partner for three consecutive years Security and privacy protection have always been the foundation to support the steady development of the consumer ...[Details]
On January 16, China Ceramics Electronics announced that the company plans to purchase the operating assets and liabilities related to the gallium nitride communication base station RF chip business ...[Details]
Speakers and receivers are usually used in battery-powered portable audio devices. Class D audio power amplifiers (Smart PAs) are used to drive speakers to provide high-power audio signals. However...[Details]
Not long ago, two primary school students in Wenzhou, Zhejiang Province, became popular online because of a video that could be called a "textbook elevator self-rescue". In the video, the two childre...[Details]
Shenzhen, China –
TITAN Haptics announces its latest innovation – TITAN Core, a compact and powerful haptic development board designed to simplify the integration of haptic technology in consum...[Details]
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
