EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

P1206E22R3BBPB

Description
Fixed Resistor, Thin Film, 0.33W, 22.3ohm, 200V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP
CategoryPassive components    The resistor   
File Size143KB,10 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

P1206E22R3BBPB Overview

Fixed Resistor, Thin Film, 0.33W, 22.3ohm, 200V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 1206, CHIP

P1206E22R3BBPB Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145039373702
package instructionCHIP
Reach Compliance Codeunknown
Country Of OriginFrance
ECCN codeEAR99
YTEOL7.9
Other featuresANTI-SULFUR, HIGH PRECISION
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length3.06 mm
Package formSMT
Package width1.6 mm
method of packingTR, PAPER
Rated power dissipation(P)0.33 W
Rated temperature70 °C
resistance22.3 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead/Silver - with Nickel barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage200 V
Atmel Launches Highly Integrated Automotive Driver IC ATA6026
On May 2, Atmel announced the launch of the highly integrated ATA6026 automotive driver integrated circuit (IC), which is the first member of the new upcoming automotive driver family. The design of t...
frozenviolet Automotive Electronics
Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" 07 Slew Rate and Full Power Bandwidth Case Analysis
[i=s]This post was last edited by 1nnocent on 2021-5-26 12:18[/i]I had some understanding of slew rate when I was playing with op amps before, but I had never calculated it specifically. However, it i...
1nnocent Analog electronics
About the battery life of SenSorTile.Box
I saw someone with extremely low battery life before, and I guessed that it was because of a short circuit in the circuit board. I suggest that you power on the phone first, check if the sensor in the...
梦璃 ST MEMS Sensor Creative Design Competition
Download and debug interface issues on product circuit boards
[align=left][size=14px]I am making a wearable device. The PCB area on the device is limited, so I want to save as much area as possible. [/size][/align][align=left][size=14px]Both chips on the board n...
b01010101 PCB Design
Multisim op amp output is greater than the power supply problem
When I used Multisim to simulate the op amp circuit before, I found that the op amp output was greater than the power rail. Sometimes I wanted to use the op amp as a comparator for open-loop simulatio...
fish001 Analogue and Mixed Signal
How to choose between DT4215 and 15B for multimeter selection
I am planning to buy a multimeter. Most of the use scenarios require testing voltages of 600-900V (occasionally overvoltages of 1000+), so I have been using Fluke's 15B+. The meters in the company are...
bigbat Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号