EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

CPWN20560R0JE013

Description
Fixed Resistor, Wire Wound, 20W, 560ohm, 5% +/-Tol, -30,30ppm/Cel,
CategoryPassive components    The resistor   
File Size96KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

CPWN20560R0JE013 Overview

Fixed Resistor, Wire Wound, 20W, 560ohm, 5% +/-Tol, -30,30ppm/Cel,

CPWN20560R0JE013 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid951583226
Reach Compliance Codeunknown
ECCN codeEAR99
YTEOL7.15
Other featuresFLAME PROOF; NON-INDUCTIVE
structureRectangular
JESD-609 codee3
Lead diameter0.813 mm
Lead length25.4 mm
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature275 °C
Minimum operating temperature-65 °C
Package height15.87 mm
Package length63.5 mm
Package formAxial
Package width12.7 mm
method of packingBULK
Rated power dissipation(P)20 W
Rated temperature40 °C
resistance560 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyWIRE WOUND
Temperature Coefficient30 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWIRE
Tolerance5%
Operating Voltage105.8301 V
TMS320F28335DSP principle and development programming
This book introduces the basic structure, working principle, application configuration and sample programs of the TMS320F28335 DSP chip newly launched by TI. The book has 13 chapters. Chapter 1 is an ...
fish001 DSP and ARM Processors
Why does the power consumption of stm32L0 increase after it enters STOP mode again after being woken up by an external interrupt in STOP mode?
The power consumption of the first entry into stop mode is correct. After being woken up by an external interrupt, the power consumption of the next entry into stop mode is 300uA higher. What is going...
StruggleMySen stm32/stm8
[TI millimeter wave radar evaluation]_4_boost board evaluation encountered problems 2
[i=s]This post was last edited by wangran_95 on 2019-12-31 08:47[/i]After using the device, I found that it was hard to find a power supply. There were two boards and two power supplies, so I had to c...
wangran_95 TI Technology Forum
Using registers to do STM8 UART1 error request help
[i=s]This post was last edited by zhang520 on 2021-10-21 15:08[/i]Error[Li006]: duplicate definitions for "_interrupt_21"; Change 21 to 20 and the system will run fine...
zhang520 stm32/stm8
BearPi-HM Nano Development Board Review 0 Unboxing and Development Environment Setup
[i=s]This post was last edited by symic on 2022-3-20 19:42[/i]I am very happy and surprised to get the opportunity to review the BearPi-HM Nano development board. Thanks to Nanjing BearPi Intelligent ...
symic Linux and Android
Let's discuss how many people you think should be invited.
[i=s]This post was last edited by Shenzhen Xiaohua on 2021-6-26 06:13[/i]Let's discuss how many people you think should be invited....
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号