EEWORLDEEWORLDEEWORLD

Part Number

Search

C0805X222M2RAC7215

Description
Ceramic Capacitor, Ceramic,
CategoryPassive components    capacitor   
File Size726KB,24 Pages
ManufacturerKEMET
Websitehttp://www.kemet.com
Download Datasheet Parametric View All

C0805X222M2RAC7215 Overview

Ceramic Capacitor, Ceramic,

C0805X222M2RAC7215 Parametric

Parameter NameAttribute value
Objectid7171298916
package instruction, 0805
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL7.75
capacitance0.0022 µF
Capacitor typeCERAMIC CAPACITOR
dielectric materialsCERAMIC
high0.78 mm
JESD-609 codee3
length2 mm
Installation featuresSURFACE MOUNT
multi-layerYes
negative tolerance20%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formSMT
method of packingTR, EMBOSSED PLASTIC, 13 INCH
positive tolerance20%
Rated (DC) voltage (URdc)200 V
size code0805
surface mountYES
Temperature characteristic codeX7R
Temperature Coefficient15% ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
width1.25 mm
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric,
6.3 – 250 VDC (Commercial Grade)
Overview
The KEMET Flexible Termination (FT-CAP) multilayer
ceramic capacitor in X7R dielectric incorporates a unique,
flexible termination system that is integrated with the
KEMET standard termination materials. A conductive silver
epoxy is utilized between the base metal and nickel barrier
layers of KEMET’s standard termination system in order
to establish pliability, while maintaining terminal strength,
solderability and electrical performance. This technology
was developed in order to address the primary failure
mode of MLCCs – flex cracks, which are typically the result
of excessive tensile and shear stresses produced during
board flexure and thermal cycling. Flexible termination
technology inhibits the transfer of board stress to the rigid
ceramic body, therefore mitigating flex cracks which can
result in low IR or short circuit failures.
Although this technology does not eliminate the potential
for mechanical damage that may propagate during extreme
environmental and handling conditions, it does provide
superior flex performance over standard termination
systems. FT-CAP complements the KEMET Open Mode,
Floating Electrode (FE-CAP), Floating Electrode with
Flexible Termination (FF-CAP) and KEMET Power Solutions
(KPS) product lines by providing a complete portfolio of flex
mitigation solutions.
Combined with the stability of an X7R dielectric and designed
to accommodate all capacitance requirements, these flex-
robust devices are RoHS-compliant, offer up to 5 mm of
flex-bend capability and exhibit a predictable change in
capacitance with respect to time and voltage. Capacitance
change with reference to ambient temperature is limited to
±15% from −55°C to +125°C.
In addition to commercial grade, automotive grade devices
are available which meet the demanding Automotive
Electronics Council's AEC–Q200 qualification requirements.
Ordering Information
C
1206
X
106
Capacitance
Code (pF)
Two
significant
digits and
number of
zeros
K
Capacitance
Tolerance
J = ±5%
K = ±10%
M = ±20%
4
R
A
C
Termination Finish
1
TU
Packaging/Grade
(C-Spec)
2
Case Size
Specification/
Ceramic
(L" x W")
Series
0603
0805
1206
1210
1808
1812
1825
2220
2225
1
Rated
Failure
Voltage
Dielectric Rate/
(VDC)
Design
9 = 6.3
8 = 10
4 = 16
3 = 25
5 = 50
1 = 100
2 = 200
A = 250
R = X7R
X = Flexible
termination
A = N/A C = 100% Matte Sn
See "Packaging
L = SnPb (5% Pb minimum)
C-Spec
Ordering
Options Table"
Additional termination finish options may be available. Contact KEMET for details.
Built Into Tomorrow
© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 1/20/2022
1
【I-Prober 520】AC and DC current testing based on closed coil method
I'm a little sorry that I posted this a little late, because the probe had a little problem when I was testing: after a certain use, the probe had no output. I thought the probe was accidentally damag...
nemo1991 Test/Measurement
MSP430FR series unused pin processing
MSP430FR series unused pin processing...
Aguilera Microcontroller MCU
Why do different simulation results appear when the parameters of this simulation routine are set the same?
Why do different simulation results appear when the parameters of this simulation routine are set the same?...
QWE4562009 Integrated technical exchanges
Keil strange compilation problem
I used STM32CUBE to generate a project. The version of the Keil compiler was 5.28. The MCU's SRAM was 64K, which should be enough for my project. However, I found that as long as the "global variables...
bigbat stm32/stm8
EEWORLD University Hall----Live Replay: TI's Latest Application of Millimeter-Wave Radar in the Automotive Field
Live replay: TI's latest applications of mmWave radar in the automotive field : https://training.eeworld.com.cn/course/6066...
hi5 Integrated technical exchanges
Design of temperature measurement system based on msp430 single chip microcomputer
This article introduces a method of measuring temperature using an msp430 microcontroller to replace the relatively backward experimental method of combining thermistors with ammeters in traditional t...
Jacktang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号